Related Experiment Video

Updated: Oct 19, 2026

Engineering 3D Cellularized Collagen Gels for Vascular Tissue Regeneration
09:23

Engineering 3D Cellularized Collagen Gels for Vascular Tissue Regeneration

Published on: June 16, 2015

Heat-induced changes in the mechanics of a collagenous tissue: isothermal, isotonic shrinkage

S S Chen1, N T Wright, J D Humphrey

  • 1Department of Mechanical Engineering, University of Maryland, Baltimore 21250, USA.

Journal of Biomechanical Engineering
|July 21, 1999
PubMed

More Related Videos

Preparation of 3D Collagen Gels and Microchannels for the Study of 3D Interactions In Vivo10:24

Preparation of 3D Collagen Gels and Microchannels for the Study of 3D Interactions In Vivo

Published on: May 9, 2016

Engineering Fibrin-based Tissue Constructs from Myofibroblasts and Application of Constraints and Strain to Induce Cell and Collagen Reorganization12:13

Engineering Fibrin-based Tissue Constructs from Myofibroblasts and Application of Constraints and Strain to Induce Cell and Collagen Reorganization

Published on: October 28, 2013

Related Concept Videos

Thermal Strain01:19

Thermal Strain

Thermal strain is a concept that arises when we consider how temperature changes affect structures. Unlike the conventional assumption that structures remain constant under load, real-world scenarios often involve temperature fluctuations that can significantly impact these structures. Consider a homogeneous rod with a uniform cross-section resting freely on a flat horizontal surface. If the rod's temperature increases, the rod elongates. This elongation is proportional to the temperature...
Plastic Behavior01:21

Plastic Behavior

A material's elastic behavior is characterized by the disappearance of stress once the load is removed, allowing the material to return to its original state. However, when stress surpasses the yield point, yielding commences, marking the onset of plastic deformation or permanent set. This change from elastic to plastic behavior is influenced by the peak stress value and the duration before the load is removed. An intriguing observation occurs when a specimen is loaded, unloaded, and reloaded.
Problem Solving on Stress and Strain01:22

Problem Solving on Stress and Strain

Stress is a quantity that describes the magnitude of a force that causes deformation, generally defined as internal force per unit area. When forces pull on an object and cause its elongation, like the stretching of an elastic band, it is called tensile stress. When forces cause the compression of an object, it is known as compressive stress. When an object is being squeezed uniformly from all sides, like a submarine in the depths of the ocean, we call this kind of stress bulk stress (or volume...
Shrinkage in Concrete01:27

Shrinkage in Concrete

Shrinkage in concrete is primarily due to water loss from evaporation, hydration of cement, or carbonation, leading to a reduction in volume. The volumetric contraction results in volumetric strain in concrete. However, in practice, shrinkage is measured as linear strain, which is one-third of the volumetric strain.
When concrete is still in its plastic state, it can undergo a decrease in volume by about 1% of its absolute volume. This decrease is known as plastic shrinkage. It arises either...
Thermal Stress01:09

Thermal Stress

If the temperature of an object is changed while it is prevented from expanding or contracting, the object is subjected to stress. The stress is compressive if the object expands in the absence of constraint and tensile if it contracts. This stress resulting from temperature change is known as thermal stress. It can be quite large and can cause damage. To avoid this stress, engineers may design components so they can expand and contract freely. For instance, on highways, gaps are deliberately...
Relation between Poisson's ratio, Modulus of Elasticity and Modulus of Rigidity01:15

Relation between Poisson's ratio, Modulus of Elasticity and Modulus of Rigidity

Deformation occurs in axial and transverse directions when an axial load is applied to a slender bar. This deformation impacts the cubic element within the bar, transforming it into either a rectangular parallelepiped or a rhombus, contingent on its orientation. This transformation process induces shearing strain. Axial loading elicits both shearing and normal strains. Applying an axial load instigates equal normal and shearing stresses on elements oriented at a 45° angle to the load axis.