Related Experiment Video

Updated: Aug 6, 2026

Subject-specific Musculoskeletal Model for Studying Bone Strain During Dynamic Motion
09:32

Subject-specific Musculoskeletal Model for Studying Bone Strain During Dynamic Motion

Published on: April 11, 2018

Theoretical stress analysis in wrist joint--neutral position and functional position

E Genda1, E Horii

  • 1Rosai Rehabilitation Engineering Center and the Orthopaedic Department, Nagoya University, Japan.

Journal of Hand Surgery (Edinburgh, Scotland)
|August 29, 2000
PubMed

More Related Videos

Setup for the Quantitative Assessment of Motion and Muscle Activity During a Virtual Modified Box and Block Test04:06

Setup for the Quantitative Assessment of Motion and Muscle Activity During a Virtual Modified Box and Block Test

Published on: January 12, 2024

A Passive Ankle Dorsiflexion Testing System for an In Vivo Model of Overuse-induced Tendinopathy04:37

A Passive Ankle Dorsiflexion Testing System for an In Vivo Model of Overuse-induced Tendinopathy

Published on: March 1, 2024

Related Concept Videos

Normal Stress01:19

Normal Stress

Normal stress is a type of stress that occurs when forces act perpendicular, or normal, to a material's cross-sectional area. This stress often arises in structures when subjected to axial loading, which is the application of force along the axis of an object. A practical example of this can be found in bridge truss members.
When a rod is under axial loading, the internal forces and corresponding stress are normal to the plane of the section, so it is termed normal stress. It's important to...
Applications of Stress01:04

Applications of Stress

Consider a structure made of a boom and a rod designed to support a load. These two components are connected by a pin and stabilized by brackets and pins. The boom and the rod are detached from their supports to assess the different stresses imposed on this structure, and a free-body diagram is drawn. Then, all the forces applied, including the load acting on the structure, are identified. The reaction forces exerted on both the boom and the rod are computed using the equilibrium equations.
The...
Stress: General Loading Conditions01:15

Stress: General Loading Conditions

To grasp the intricacy of real-world conditions where multiple loads are applied simultaneously to a structure, one might visualize a section passing through a specific point within a body, aligned parallel to the xy plane. This section is subjected to various forces, including original loads, normal forces, and shearing forces.
The shearing force, possessing potential directionality within the plane of the section, is simplified into two component forces running parallel to the x and y axes.
Components of Stress01:23

Components of Stress

Stress analysis under multiple loading conditions is intricate, necessitating a comprehensive grasp of normal and shearing stresses. Consider a small cube at point O, subjected to stress on all six faces, visible or not. Normal stress components σx, σy, σz act perpendicularly to the x, y, and z axes. Shearing stress components τxy and τxz are exerted on faces perpendicular to these axes.
Interestingly, the hidden cube faces also experience these stresses, equal and opposite to those on the...
Principal Stresses01:24

Principal Stresses

The graphical depiction of normal and shearing stress equations is represented by a circle, demonstrating the interplay between these stresses under different angular conditions. The center of this circle C, located on the vertical axis, represents the average normal stress, while its radius shows the range of stress variations. At points A and B, where the circle intersects the horizontal axis, the maximum and minimum normal stresses are observed, occurring without shearing stress. These...
Stresses under Combined Loadings01:23

Stresses under Combined Loadings

When analyzing a bent tube with a circular cross-section subjected to multiple forces, it is crucial to determine the stress distribution in order to maintain structural integrity under varied load conditions.
The process begins by slicing the tube at critical points and analyzing the internal forces and stress components at these sections, focusing on the centroid. Normal stresses, generated by axial forces and bending moments, are either compressive or tensile and vary across the section from...