Related Experiment Video

Updated: Aug 12, 2026

Cooling Rate Dependent Ellipsometry Measurements to Determine the Dynamics of Thin Glassy Films
09:32

Cooling Rate Dependent Ellipsometry Measurements to Determine the Dynamics of Thin Glassy Films

Published on: January 26, 2016

Is it reasonable to assume a uniformly distributed cooling-rate along the microslide of a directional solidification

Rabin1

  • 1Department of Mechanical Engineering, Technion - Israel Institute of Technology, Haifa 32000, Israel.

Journal of Microscopy
|September 30, 2000
PubMed

More Related Videos

Experimental Methods for Investigation of Shape Memory Based Elastocaloric Cooling Processes and Model Validation11:11

Experimental Methods for Investigation of Shape Memory Based Elastocaloric Cooling Processes and Model Validation

Published on: May 2, 2016

Ice Generation and the Heat and Mass Transfer Phenomena of Introducing Water to a Cold Bath of Brine08:16

Ice Generation and the Heat and Mass Transfer Phenomena of Introducing Water to a Cold Bath of Brine

Published on: March 13, 2017

Related Concept Videos

Phase Transitions: Melting and Freezing02:39

Phase Transitions: Melting and Freezing

Heating a crystalline solid increases the average energy of its atoms, molecules, or ions, and the solid gets hotter. At some point, the added energy becomes large enough to partially overcome the forces holding the molecules or ions of the solid in their fixed positions, and the solid begins the process of transitioning to the liquid state or melting. At this point, the temperature of the solid stops rising, despite the continual input of heat, and it remains constant until all of the solid is...
Recrystallization: Solid–Solution Equilibria01:10

Recrystallization: Solid–Solution Equilibria

Recrystallization is a purification technique used to separate impurities from solid compounds. In this technique, no chemical reactions occur. Instead, it exploits physical properties only, specifically, the solubility differences between the desired compound and impurities, either at a single temperature or at different temperatures, and under other selected conditions. The solid-solution equilibrium (solubility equilibrium) of each component in the solution represents a binary phase...
Temperature Dependent Deformation01:12

Temperature Dependent Deformation

In a nonhomogeneous rod made up of steel and brass, restrained at both ends and subjected to a temperature change, several steps are involved in calculating the stress and compressive load. Due to the problem's static indeterminacy, one end support is disconnected, allowing the rod to experience the temperature change freely. Next, an unknown force is applied at the free end, triggering deformations in the rod's steel and brass portions. These deformations are then calculated and added together...
Solid–Solid Solutions01:24

Solid–Solid Solutions

The temperature-composition phase diagram of two solids, A and B, which are immiscible in the solid phase but form miscible liquids, shows that when the temperature is low, these two exist as separate, pure solids (A and B). As the temperature increases, they transition into a single-phase liquid solution where A and B coexist. Moving from point a1 to a2 in the phase diagram, the composition changes such that solid B begins to separate from the solution, enriching the remaining liquid with A.
Steady, Laminar Flow Between Parallel Plates01:17

Steady, Laminar Flow Between Parallel Plates

Understanding steady, laminar flow between parallel plates is essential for analyzing and designing flow in narrow rectangular channels, commonly found in various water conveyance and drainage systems. The Navier-Stokes equations govern fluid motion and are generally challenging to solve due to their nonlinearity. However, simplifications are possible in certain cases, like the steady laminar flow between parallel plates. For this scenario, we assume steady, incompressible, laminar flow.
Steady, Laminar Flow in Circular Tubes01:23

Steady, Laminar Flow in Circular Tubes

Hagen-Poiseuille flow describes a viscous fluid's steady, incompressible flow through a cylindrical tube with a constant radius R. This flow profile is often applied to understand fluid transport in narrow channels, such as capillaries. It serves as a foundational example of laminar flow. In this model, cylindrical coordinates (r,θ,z) are used to describe the radial (r), angular (θ), and axial (z) dimensions within the tube. For Hagen-Poiseuille flow, the velocity profile is purely axial,...