Related Experiment Video

Updated: Aug 4, 2026

Quantification of Levator Ani Hiatus Enlargement by Magnetic Resonance Imaging in Males and Females with Pelvic Organ Prolapse
07:41

Quantification of Levator Ani Hiatus Enlargement by Magnetic Resonance Imaging in Males and Females with Pelvic Organ Prolapse

Published on: April 17, 2019

Pelvic angles: a mathematically rigorous definition which is consistent with a conventional clinical understanding of

R Baker1

  • 1Gait Analysis Service, Musgrave Park Hospital, Stockman's Lane, Belfast BT9 7JB, Northern Ireland, UK. richard.baker@greenpark.n-i.nhs.uk

Gait & Posture
|February 13, 2001
PubMed

More Related Videos

A Postoperative Evaluation Guideline for Computer-Assisted Reconstruction of the Mandible10:42

A Postoperative Evaluation Guideline for Computer-Assisted Reconstruction of the Mandible

Published on: January 28, 2020

Three-Dimensional Preoperative Virtual Planning in Derotational Proximal Femoral Osteotomy08:15

Three-Dimensional Preoperative Virtual Planning in Derotational Proximal Femoral Osteotomy

Published on: February 17, 2023

Related Concept Videos

Relating Angular And Linear Quantities - I01:09

Relating Angular And Linear Quantities - I

If the rotational definitions are compared with the definitions of linear kinematic variables from motion along a straight line and motion in two and three dimensions, we can observe a mapping of the linear variables to the rotational ones.
When comparing the linear and rotational variables individually, the linear variable of position has physical units of meters, whereas the angular position variable has dimensionless units of radians, as it is the ratio of two lengths. The linear velocity...
Accuracy, limits, and approximation01:28

Accuracy, limits, and approximation

Accuracy, limits, and approximations are common in many fields, especially in engineering calculations. These concepts are imperative for ensuring that a given value is as close as possible to its true value.
Accuracy is defined as the closeness of the measured value to the true or actual value. In engineering mechanics, repeated measurements are taken during theoretical or experimental analyses to ensure that the result is precise and accurate.
The accuracy of any solution is based on the...
Unsymmetric Bending - Angle of Neutral Axis01:15

Unsymmetric Bending - Angle of Neutral Axis

Unsymmetrical bending occurs when a structural member is subjected to bending moments in a plane that does not align with the member's principal axes. This scenario typically arises in beams and other structural components when loads are applied at non-ideal angles, introducing complexities in stress analysis.
When a bending moment is applied at an angle θ concerning the vertical axis of a symmetrical member, it can be resolved into components along the member's principal centroidal axes. The...
Design Example: Traverse Angle Computations01:25

Design Example: Traverse Angle Computations

Traverse angle computations are a critical component of surveying, used to compute the internal angles within a closed traverse. A traverse consists of a series of connected lines forming a closed loop, often used for land boundary delineation or mapping. Calculating the internal angles ensures accuracy in the traverse geometry and is essential for checking survey data integrity.The process begins with known azimuths and bearings of the traverse sides. Internal angles at each vertex are...
Adjusting a Traverse01:12

Adjusting a Traverse

In the site survey of a four-sided traverse, internal angles are essential to ensure geometric accuracy. The survey revealed that the sum of the measured internal angles was 359 degrees and 48 minutes, which is 12 minutes less than the expected 360 degrees. This discrepancy signals an error likely arising from measurement inaccuracies during the fieldwork.To rectify this error, the adjustment process involved distributing the 12-minute shortfall equally across the four internal angles. By...
Inclination of a Line01:25

Inclination of a Line

The inclination of a line describes its angle of tilt with respect to the horizontal axis. While a line itself is an abstract object with no thickness, its orientation on the Cartesian plane is determined by its slope, which reflects how steeply it rises or falls. The inclination angle, always measured counterclockwise from the positive x-axis, varies between zero and π radians for nonhorizontal lines. This angle directly relates to the slope, providing a geometric interpretation of the line's...