Related Experiment Video

Updated: Aug 7, 2026

An Analog Macroscopic Technique for Studying Molecular Hydrodynamic Processes in Dense Gases and Liquids
11:03

An Analog Macroscopic Technique for Studying Molecular Hydrodynamic Processes in Dense Gases and Liquids

Published on: December 4, 2017

Dynamic long-term anticipation of chaotic states

H U Voss1

  • 1Department of Physics, University of Freiburg, Freiburg, Germany. hv@physik.uni-freiburg.de

Physical Review Letters
|July 20, 2001
PubMed

More Related Videos

Three Laboratory Procedures for Assessing Different Manifestations of Impulsivity in Rats09:12

Three Laboratory Procedures for Assessing Different Manifestations of Impulsivity in Rats

Published on: March 17, 2019

Age-dependent Dynamics of Locomotion in Caenorhabditis elegans: A Lyapunov Exponent Analysis06:44

Age-dependent Dynamics of Locomotion in Caenorhabditis elegans: A Lyapunov Exponent Analysis

Published on: September 23, 2025

Related Concept Videos

Entropy Change in Reversible Processes01:10

Entropy Change in Reversible Processes

In the Carnot engine, which achieves the maximum efficiency between two reservoirs of fixed temperatures, the total change in entropy is zero. The observation can be generalized by considering any reversible cyclic process consisting of many Carnot cycles. Thus, it can be stated that the total entropy change of any ideal reversible cycle is zero.
The statement can be further generalized to prove that entropy is a state function. Take a cyclic process between any two points on a p-V diagram.
The Entropy as a State Function01:14

The Entropy as a State Function

Consider an arbitrary process that moves between two specific states (A and B) in a cyclic manner. This process is reversible and broken down into smaller parts that each follow a Carnot cycle. A Carnot cycle has two isothermal (constant temperature) processes. During these processes, the ratio of the amount of heat transferred to their respective temperature remains constant. The other two processes in the Carnot cycle are also reversible but adiabatic, which means they occur without any heat...
Entropy Changes Accompanying Specific Processes01:21

Entropy Changes Accompanying Specific Processes

Entropy, a measure of disorder in a system, changes during phase transitions like freezing or boiling. At the transition temperature Ttrs, where two phases are in equilibrium, the phase transition is a reversible process. The entropy change can be calculated from a substance's enthalpy of transition using the equation ΔStrs = ΔtrsH /Ttrs.When a perfect gas expands isothermally from one volume to another, entropy increases logarithmically with volume. Conversely, isothermal compression results...
State Space Representation01:27

State Space Representation

The frequency-domain technique, commonly used in analyzing and designing feedback control systems, is effective for linear, time-invariant systems. However, it falls short when dealing with nonlinear, time-varying, and multiple-input multiple-output systems. The time-domain or state-space approach addresses these limitations by utilizing state variables to construct simultaneous, first-order differential equations, known as state equations, for an nth-order system.
Consider an RLC circuit, a...
Linear Approximation in Time Domain01:21

Linear Approximation in Time Domain

Nonlinear systems often require sophisticated approaches for accurate modeling and analysis, with state-space representation being particularly effective. This method is especially useful for systems where variables and parameters vary with time or operating conditions, such as in a simple pendulum or a translational mechanical system with nonlinear springs.
For a simple pendulum with a mass evenly distributed along its length and the center of mass located at half the pendulum's length, the...
Multimachine Stability01:25

Multimachine Stability

Multimachine stability analysis is crucial for understanding the dynamics and stability of power systems with multiple synchronous machines. The objective is to solve the swing equations for a network of M machines connected to an N-bus power system.
In analyzing the system, the nodal equations represent the relationship between bus voltages, machine voltages, and machine currents. The nodal equation is given by: