Jove
Visualize
Contact Us
JoVE
x logofacebook logolinkedin logoyoutube logo
ABOUT JoVE
OverviewLeadershipBlogJoVE Help Center
AUTHORS
Publishing ProcessEditorial BoardScope & PoliciesPeer ReviewFAQSubmit
LIBRARIANS
TestimonialsSubscriptionsAccessResourcesLibrary Advisory BoardFAQ
RESEARCH
JoVE JournalMethods CollectionsJoVE Encyclopedia of ExperimentsArchive
EDUCATION
JoVE CoreJoVE BusinessJoVE Science EducationJoVE Lab ManualFaculty Resource CenterFaculty Site
Terms & Conditions of Use
Privacy Policy
Policies

Related Concept Videos

Strength of Cement01:20

Strength of Cement

Strength tests for cement are not performed directly on neat cement paste due to difficulty in obtaining consistent, reliable specimens. Instead, cement is typically tested in the form of cement-sand mortar.
For compressive strength tests, ASTM C 109-05 standards prescribe a cement-sand mix ratio of 1:2.75 and a water/cement ratio of 0.485 for making 2-inch cubes. These cubes are mixed, cast, and cured in saturated lime water at 23°C until testing. Flexural strength testing, outlined in ASTM C...
Toughness and Hardness of Aggregate01:22

Toughness and Hardness of Aggregate

Toughness and hardness are critical properties of aggregate materials used in concrete, particularly on pavement surfaces and industrial flooring subjected to heavy loads. Toughness is defined as the aggregate's resistance to failure by impact and is measured by the aggregate impact value (AIV). For this, the aggregate impact value test is performed, wherein the impact is delivered by a standard hammer, which falls freely under its own weight onto the aggregates. The aggregates fragment in the...
Compacting Factor test01:22

Compacting Factor test

The compacting factor test is a method used to assess the workability of concrete. It is  especially suitable for concrete mixes containing aggregates up to one and a half inches in size. This test involves specialized equipment consisting of two truncated cone-shaped hoppers and a cylinder, all with polished interior surfaces to minimize friction.
The procedure begins by placing concrete into the upper hopper without any compaction. Once filled, the bottom door of this hopper is opened,...
Non-destructive Tests for Concrete Strength01:12

Non-destructive Tests for Concrete Strength

The rebound hammer test, also known as the Schmidt hammer test, is a non-destructive technique for evaluating the hardness of concrete and, indirectly, the strength of concrete. It operates on the principle that the rebound of a spring-driven mass from a concrete surface correlates to the surface's hardness. The device comprises a mass within a tubular housing, a spring mechanism, and a plunger that strikes the concrete. Upon release, the energy imparted to the mass by the spring causes it to...
Relation Between Tensile Strength and Compressive Strength of Concrete01:30

Relation Between Tensile Strength and Compressive Strength of Concrete

Concrete is a fundamental building material, and understanding its strengths is crucial for construction projects. The relationship between its tensile and compressive strengths is intricate, showing that while these strengths are related, they do not increase at the same rate. Tensile strength's growth is slower and is affected by various factors such as the methods used for testing, the size and shape of the specimen, the texture of the aggregate used, and the moisture content of the concrete.
Mechanical Characteristics of Steel01:18

Mechanical Characteristics of Steel

The mechanical characteristics of steel are assessed through various tests that evaluate its strength, toughness, and flexibility. These tests include tension, torsion, impact, bending, and hardness assessments, each providing crucial information about steel's suitability for specific applications.
The tension test is fundamental for determining tensile strength. In this test, a steel specimen is stretched using a gripping device until it breaks. The data collected during this test are used to...

You might also read

Related Articles

Articles linked to this work by shared authors, journal, and citation graph.

Sort by
Same author

COVID-19 and Pregnancy: A Prospective Descriptive Study from a Tertiary Hospital in Nigeria.

West African journal of medicine·2021
Same author

Cross-sectional study of the prevalence, causes and management of hospital-onset diarrhoea.

The Journal of hospital infection·2019
Same author

Cost-effectiveness of outpatient parenteral antibiotic therapy: a simulation modelling approach.

The Journal of antimicrobial chemotherapy·2017
Same author

TNM 8th edition: Sentinel Lymph Node Biopsy in stage T1b melanoma.

Journal of plastic, reconstructive & aesthetic surgery : JPRAS·2017
Same author

Community IntraVenous Antibiotic Study (CIVAS): protocol for an evaluation of patient preferences for and cost-effectiveness of community intravenous antibiotic services.

BMJ open·2015
Same author

Current concepts in the management of prosthetic joint infection.

Internal medicine journal·2014

Related Experiment Video

Updated: Jul 27, 2026

Predicting Catalyst Extrudate Breakage Based on the Modulus of Rupture
09:53

Predicting Catalyst Extrudate Breakage Based on the Modulus of Rupture

Published on: May 13, 2018

Mechanical strength testing of compacted powders.

P Stanley1

  • 1The Manchester School of Engineering, Simon Building, University of Manchester, Oxford Road, Manchester M139PL, UK.

International Journal of Pharmaceutics
|September 21, 2001
PubMed
Summary

New test specimens offer a better way to measure the fracture stress of brittle materials like compacted powders. A statistical method is also presented for analyzing strength test data.

Area of Science:

  • Materials Science
  • Solid Mechanics
  • Statistical Analysis

Background:

  • Determining the fracture stress of brittle materials is crucial for understanding their mechanical behavior.
  • Traditional test methods may not be suitable for all brittle materials, such as compacted powders.

Purpose of the Study:

  • To introduce and evaluate alternative test specimens for measuring the fracture stress of brittle materials.
  • To outline a statistical approach for processing strength test data obtained from these specimens.

Main Methods:

  • Description and discussion of novel test specimen designs.
  • Application of statistical methods for data analysis of fracture stress measurements.

Main Results:

More Related Videos

A Uniaxial Compression Experiment with CO2-Bearing Coal Using a Visualized and Constant-Volume Gas-Solid Coupling Test System
10:27

A Uniaxial Compression Experiment with CO2-Bearing Coal Using a Visualized and Constant-Volume Gas-Solid Coupling Test System

Published on: June 12, 2019

Determining the Mechanical Strength of Ultra-Fine-Grained Metals
05:04

Determining the Mechanical Strength of Ultra-Fine-Grained Metals

Published on: November 22, 2021

Related Experiment Videos

Last Updated: Jul 27, 2026

Predicting Catalyst Extrudate Breakage Based on the Modulus of Rupture
09:53

Predicting Catalyst Extrudate Breakage Based on the Modulus of Rupture

Published on: May 13, 2018

A Uniaxial Compression Experiment with CO2-Bearing Coal Using a Visualized and Constant-Volume Gas-Solid Coupling Test System
10:27

A Uniaxial Compression Experiment with CO2-Bearing Coal Using a Visualized and Constant-Volume Gas-Solid Coupling Test System

Published on: June 12, 2019

Determining the Mechanical Strength of Ultra-Fine-Grained Metals
05:04

Determining the Mechanical Strength of Ultra-Fine-Grained Metals

Published on: November 22, 2021

  • The proposed alternative test specimens are suitable for determining the fracture stress of brittle materials.
  • The statistical approach provides a robust framework for processing strength test data.

    • Conclusions:

    • Alternative test specimens enhance the accurate determination of fracture stress in brittle materials.
    • Statistical processing of strength data is essential for reliable material characterization.