W-plasty and geometric broken line closure.
B J Rodgers1, E F Williams, C R Hove
1Rodgers Center for Facial Plastic Surgery, Boise, ID, USA.
Facial Plastic Surgery : FPS
|December 6, 2001
Summary
Scar revision techniques like W-plasty and geometric broken line closure improve appearance by irregularizing scars. These methods offer benefits for scars over 2 cm or 2 mm, balancing risks and rewards.
Area of Science:
- Plastic Surgery
- Dermatology
- Wound Healing
Background:
- Scar revision decisions involve risk-benefit analysis.
- Scars exceeding 2 cm in length or 2 mm in width are candidates for improvement.
- Scar irregularization is a long-standing technique for camouflage.
Purpose of the Study:
- To discuss scar irregularization techniques for camouflage.
- To compare W-plasty and geometric broken line closure for scar revision.
- To analyze the advantages, disadvantages, and design principles of each method.
Main Methods:
- Review of scar irregularization techniques.
- Focus on W-plasty for regularly irregular scars.
- Focus on geometric broken line closure for irregularly irregular scars.
Main Results:
- Both W-plasty and geometric broken line closure can yield excellent results.
- Technique effectiveness depends on correct application and appropriate patient selection.
- Detailed discussion of the pros, cons, and design considerations for each method.
Conclusions:
- Scar irregularization, via W-plasty or geometric broken line closure, is effective for scar camouflage.
- Appropriate technique selection is crucial for optimal scar revision outcomes.
- Risk-benefit assessment guides the decision for scar revision.
Related Concept Videos
00:58Plasticity
Plasticity is the property where an object loses its elasticity and undergoes irreversible deformation, even after the deformation forces are eliminated. If a material deforms irreversibly without increasing stress or load, then this is called ideal plasticity. For example, when a force is applied to an aluminum rod, it changes its shape, but it does not return to its original shape once the force is removed. Plastic deformation or ductility is thus a permanent deformation or change in the...
01:18Deformations in a Symmetric Member in Bending
When analyzing the deformation of a symmetric prismatic member subjected to bending by equal and opposite couples, it becomes clear that as the member bends, the originally straight lines on its wider faces curve into circular arcs, with a constant radius centered at a point known as Point C. This phenomenon helps to understand the stress and strain distribution within the member more clearly.
When the member is segmented into tiny cubic elements, it is observed that the primary stress...
When the member is segmented into tiny cubic elements, it is observed that the primary stress...
01:14Plastic Deformations
It is essential to understand how structural members behave under plastic deformation when the bending stress exceeds the material's yield strength. This state of deformation permanently alters the shape of the member, in contrast to the linear elastic behavior observed before yielding. The strain at any point in the member is expressed in terms of maximum strain. Notably, the neutral axis, which coincides with the centroid during elastic bending, shifts away from the centroid under plastic...
01:21Plastic Deformations of Members with a Single Plane of Symmetry
When a structural member undergoes plastic deformation due to bending, it is crucial to understand the position of the neutral axis and the stress distribution. This member, characterized by a single plane of symmetry, exhibits a uniform stress distribution, with negative stress above the neutral axis and positive stress below. Notably, the neutral axis does not align with the centroid of the cross-section. This misalignment is typical in cases where the cross-section is not rectangular or...
01:19Plastic Deformations
Plastic deformation represents a fundamental concept in materials science, which explains the irreversible change in the shape of a material when it experiences stress beyond its elastic capability. This phenomenon is important in structural engineering, especially in designing and analyzing cantilever beams—structures that are securely fixed at one end and bear loads at the opposite end. When these beams are subjected to loads within their elastic range, they will return to their original...
01:30Geometry of Hyperbolas
A hyperbola consists of all points where the absolute difference of distances to two fixed points, called foci, remains constant. The standard equation isEach branch extends infinitely and approaches two asymptotes, which guide the curve’s behavior. The parameters a and b define key features: a measures the distance from the center to each vertex along the transverse axis, while b influences the slopes of the asymptotes. The asymptotes have equationsA rectangle centered at the origin with...