Jove
Visualize
Contact Us
JoVE
x logofacebook logolinkedin logoyoutube logo
ABOUT JoVE
OverviewLeadershipBlogJoVE Help Center
AUTHORS
Publishing ProcessEditorial BoardScope & PoliciesPeer ReviewFAQSubmit
LIBRARIANS
TestimonialsSubscriptionsAccessResourcesLibrary Advisory BoardFAQ
RESEARCH
JoVE JournalMethods CollectionsJoVE Encyclopedia of ExperimentsArchive
EDUCATION
JoVE CoreJoVE BusinessJoVE Science EducationJoVE Lab ManualFaculty Resource CenterFaculty Site
Terms & Conditions of Use
Privacy Policy
Policies

Related Concept Videos

Stress Concentrations01:24

Stress Concentrations

Stress concentration is when stress intensifies near discontinuities such as holes or abrupt cross-sectional changes in a structural member. This localized stress can often surpass the average stress within the member. The stress distribution in flat bars, either with a circular hole or varying widths connected by fillets, can be determined experimentally using a photoelastic method. The results are based on ratios of geometric parameters like the ratio of the hole's radius to the smaller width...
Thin-Walled Hollow Shafts01:15

Thin-Walled Hollow Shafts

In analyzing a thin-walled hollow shaft subjected to torsional loading, a segment with width dx is isolated for examination. Despite its equilibrium state, this segment faces torsional shearing forces at its ends. These forces are quantitatively described by the product of the longitudinal shearing stress on the segment's minor surface and the area of this surface, leading to the concept of shear flow. This shear flow is consistent throughout the structure, indicating a uniform distribution of...
Distribution of Stresses in a Narrow Rectangular Beam01:11

Distribution of Stresses in a Narrow Rectangular Beam

In studying beam stress distribution, examining an elemental section is essential. To determine the average shearing stress on this face, the calculated shear is divided by the surface area. Importantly, shearing stresses on the beam's transverse and horizontal planes mirror each other, indicating a consistent stress distribution along the upper region of the beam. Notably, shearing stresses are absent at the beam's upper and lower surfaces due to the absence of applied forces in these areas.
Unsymmetric Loading of Thin-Walled Members01:23

Unsymmetric Loading of Thin-Walled Members

Thin-walled members with non-symmetrical cross-sections are vital to engineering structures, offering material efficiency and structural integrity. However, unsymmetrical loading on these members leads to complex stress distributions, resulting in simultaneous bending and twisting can cause deformation or structural failure. The interaction between bending and twisting requires detailed analysis to ensure structural resilience.
The concept of the shear center is crucial in countering the...
Unsymmetric Loading of Thin-Walled Members: Problem Solving01:07

Unsymmetric Loading of Thin-Walled Members: Problem Solving

The shear center of a channel section with uniform thickness, height, and width, is determined by computing the shear force in the member and calculating the moments of inertia of the sections.
To compute the shear forces, find the shear flow at a specific distance from the endpoint using the vertical shear and the moment of inertia values. The total shear force on the flange is calculated by integrating the shear flow from one end of the flange to the other.
Next, calculate the moments of...
Spanning Openings in Brick Walls01:20

Spanning Openings in Brick Walls

In brick wall construction, supporting structures are crucial for openings like windows and doors to maintain the integrity and support the weight of the wall above. These supports include lintels, corbels, and arches, each serving specific structural purposes.
Lintels are primary supports used to span openings and can be crafted from materials such as reinforced concrete, steel-reinforced brick masonry, or simple steel angles. These are straightforward to install and are typically concealed...

You might also read

Related Articles

Articles linked to this work by shared authors, journal, and citation graph.

Sort by
Same author

Durable ventricular assist devices for patients with advanced heart failure: the New Zealand experience.

The New Zealand medical journal·2024
Same author

Publisher Correction: Correcting bias in cardiac geometries derived from multimodal images using spatiotemporal mapping.

Scientific reports·2023
Same author

Non-contact quantification of aortic stenosis and mitral regurgitation using carotid waveforms from skin displacements.

Physiological measurement·2023
Same author

Correcting bias in cardiac geometries derived from multimodal images using spatiotemporal mapping.

Scientific reports·2023
Same author

Impaired calcium handling mechanisms in atrial trabeculae of diabetic patients.

Physiological reports·2023
Same author

MITEA: A dataset for machine learning segmentation of the left ventricle in 3D echocardiography using subject-specific labels from cardiac magnetic resonance imaging.

Frontiers in cardiovascular medicine·2023

Related Experiment Video

Updated: Jul 15, 2026

Casting Protocols for the Production of Open Cell Aluminum Foams by the Replication Technique and the Effect on Porosity
09:22

Casting Protocols for the Production of Open Cell Aluminum Foams by the Replication Technique and the Effect on Porosity

Published on: December 11, 2014

Stent strut thickness and restenosis

John A Ormiston, Mark W I Webster, Peter N Ruygrok

    Circulation
    |January 16, 2002
    PubMed
    Summary

    No abstract available in PubMed .

    More Related Videos

    Performing Microscope-Mounted Y-Shaped Cutting Tests
    06:15

    Performing Microscope-Mounted Y-Shaped Cutting Tests

    Published on: January 20, 2023

    Measuring the Structure, Composition, and Change of Underwater Environments with Large-area Imaging
    09:19

    Measuring the Structure, Composition, and Change of Underwater Environments with Large-area Imaging

    Published on: April 18, 2025

    Related Experiment Videos

    Last Updated: Jul 15, 2026

    Casting Protocols for the Production of Open Cell Aluminum Foams by the Replication Technique and the Effect on Porosity
    09:22

    Casting Protocols for the Production of Open Cell Aluminum Foams by the Replication Technique and the Effect on Porosity

    Published on: December 11, 2014

    Performing Microscope-Mounted Y-Shaped Cutting Tests
    06:15

    Performing Microscope-Mounted Y-Shaped Cutting Tests

    Published on: January 20, 2023

    Measuring the Structure, Composition, and Change of Underwater Environments with Large-area Imaging
    09:19

    Measuring the Structure, Composition, and Change of Underwater Environments with Large-area Imaging

    Published on: April 18, 2025