Related Experiment Video

Updated: Jul 14, 2026

Fabrication of Superhydrophobic Metal Surfaces for Anti-Icing Applications
11:20

Fabrication of Superhydrophobic Metal Surfaces for Anti-Icing Applications

Published on: August 15, 2018

Mass balance of polar ice sheets

Eric Rignot1, Robert H Thomas

  • 1Jet Propulsion Laboratory, California Institute of Technology, Mail Stop 300-235, Pasadena, CA 91109, USA. eric@adelie.jpl.nasa.gov

Science (New York, N.Y.)
|August 31, 2002
PubMed

More Related Videos

Development and Implementation of a Multi-Disciplinary Technology Enhanced Care Pathway for Youth and Adults with Concussion08:13

Development and Implementation of a Multi-Disciplinary Technology Enhanced Care Pathway for Youth and Adults with Concussion

Published on: January 20, 2019

Determination of the Friction Coefficients of Icy Pavements Under Different Amounts of Snowfall12:21

Determination of the Friction Coefficients of Icy Pavements Under Different Amounts of Snowfall

Published on: January 6, 2023

Related Concept Videos

Static Equilibrium - I01:05

Static Equilibrium - I

A rigid body is said to be in dynamic equilibrium when both its linear and angular acceleration are zero, relative to an inertial frame of reference. This means that a body in equilibrium can be moving, but only when its linear and angular velocities are constant. A rigid body is said to be in static equilibrium when it is at rest in the selected frame of reference. The distinction between static equilibrium (e.g., a state of rest) and dynamic equilibrium (e.g, a state of uniform motion) is...
Static Equilibrium - II01:07

Static Equilibrium - II

Static equilibrium is a special case in mechanics that is very important in everyday life. It occurs when the net force and the net torque on an object or system are both zero. This means that both the linear and angular accelerations are zero. Thus, the object is at rest, or its center of mass is moving at a constant velocity. However, this does not mean that no forces are acting on the object within the system. In fact, there are very few scenarios on Earth in which no forces are acting upon...
Frost Action on Concrete01:27

Frost Action on Concrete

Concrete structures in cold climates, such as those along roadsides, can retain moisture. This moisture makes them susceptible to frost-related damage when temperatures fall below freezing. Adding moisture worsens the damage during temperature fluctuations, leading to repeated freezing and thawing. De-icing salts, spread over these structures to melt ice, add to the freeze-thaw cycle, and draw even more moisture into the concrete.
This freeze-thaw cycle primarily causes surface scaling, where...
Frost Resistant Concrete01:29

Frost Resistant Concrete

Concrete's susceptibility to frost damage during freeze-thaw cycles demands strategic measures to enhance its frost resistance. Employing techniques like air entrainment, adjusting the water-cement ratio, proper curing, and selecting appropriate aggregates are essential.
Introducing microscopic air bubbles into the concrete mix through air entrainment creates small voids that accommodate ice expansion, thereby reducing internal pressures and preventing cracking. The optimal amount of entrained...
Average Value on a Rectangle01:27

Average Value on a Rectangle

A snowfall map can represent how snow depth varies across a region, such as Colorado, over a fixed time period. Since different locations may receive different amounts of snow, the snowfall depth is described by a function of two variables. If f(x,y) represents the snow depth at a point in a rectangular region, then the average snowfall over the entire region is found by comparing the total accumulated snowfall with the area being measured.Total Snowfall over a RegionThe total snowfall over a...
Moments and Centers of Mass01:23

Moments and Centers of Mass

A flat metal plate, or lamina, balances at a point called its center of mass. This point depends not only on the shape of the plate but also on how mass is distributed throughout it. If the material has variable density, some regions contribute more to the balance point than others. Mathematically, the center of mass is treated as a weighted average of all points in the plate, where the weights are determined by density.Suppose the plate occupies a region D in the xy-plane, and its density at...