Related Experiment Video

Updated: Aug 12, 2026

Studying the Neural Basis of Adaptive Locomotor Behavior in Insects
10:19

Studying the Neural Basis of Adaptive Locomotor Behavior in Insects

Published on: April 13, 2011

Mechanical models for insect locomotion: active muscles and energy losses

John Schmitt1, Philip Holmes

  • 1Department of Mechanical and Aerospace Engineering, Princeton University, Princeton, NJ 08544, USA.

Biological Cybernetics
|July 2, 2003
PubMed

More Related Videos

Subject-specific Musculoskeletal Model for Studying Bone Strain During Dynamic Motion09:32

Subject-specific Musculoskeletal Model for Studying Bone Strain During Dynamic Motion

Published on: April 11, 2018

"Avatar", a Modified Ex vivo Work Loop Experiments Using In vivo Strain and Activation07:03

"Avatar", a Modified Ex vivo Work Loop Experiments Using In vivo Strain and Activation

Published on: August 18, 2023

Related Concept Videos

Actin Treadmilling01:18

Actin Treadmilling

Actin filaments undergo polymerization and depolymerization from either end. The polymerization and depolymerization rates depend on the cytosolic concentration of free G-actins. The polymerization rate is generally higher at the plus or barbed end, while the depolymerization rate is higher at the minus or pointed end. At a steady state, critical concentration describes the concentration of free G-actin monomers at which the polymerization rate at the plus end is equal to that of the...
Static and Kinetic Frictional Force01:05

Static and Kinetic Frictional Force

One of the simpler characteristics of sliding friction is that it is parallel to the contact surfaces between systems, and is always in a direction that opposes the motion or attempted motion of the systems relative to each other. If two systems are in contact and moving relative to one another, then the friction between them is called kinetic friction. For example, kinetic friction slows a hockey puck sliding on ice.
However, if two systems are in contact and are stationary relative to one...
Work and Energy for Variable Forces01:10

Work and Energy for Variable Forces

When an object is acted upon by a variable force, the amount of work done and the change in energy of the object can be more complex to calculate compared to when a constant force is applied. Work is the product of force and displacement, while energy is the capacity of a system to do work. When a constant force is applied to an object, the work done can be calculated as the product of the force and the distance moved in the direction of the force. However, when a variable force is applied, the...
Design Example: Frog Muscle Response01:14

Design Example: Frog Muscle Response

A student is tasked to work on an intriguing experiment involving an RL (Resistor-Inductor) circuit to study the muscle response of a frog's leg to electrical stimulation. The RL circuit plays a crucial role in this experiment, providing the means to control and measure the electrical impulses that trigger muscle contraction.
When the switch connecting the RL circuit is closed, a brief muscle contraction is observed. This is because, at a steady state, the inductor acts like a short circuit,...
Mechanical Systems01:22

Mechanical Systems

Mechanical systems are analogous to to electrical networks where springs and masses play similar roles to inductors and capacitors, respectively. A viscous damper in mechanical systems functions similarly to a resistor in electrical networks, dissipating energy. The forces acting on a mass in such systems include an applied force in the direction of motion, counteracted by forces from the spring, a viscous damper, and the mass's acceleration. This interplay of forces is mathematically described...
Wind Turbine Machine Models01:24

Wind Turbine Machine Models

In the growing field of wind energy, incorporating wind turbine models into transient stability analysis is essential. Induction and synchronous machines are the primary models used, with induction machines being prevalent due to their simplicity and reliability.
Induction machines interact through the rotating magnetic field generated by the stator and the rotor. The key parameter is slip, which is the difference between synchronous speed and rotor speed relative to synchronous speed. Slip is...