Related Experiment Video

Updated: Sep 21, 2026

Mesocosm-Scale Constructed Wetland Design for Wastewater Treatment
08:24

Mesocosm-Scale Constructed Wetland Design for Wastewater Treatment

Published on: May 2, 2025

Design and technical adjustment of a water treatment system: 15 years of experience

Katja Martin1, Erick Laydet, Bernard Canaud

  • 1Dialysis Research and Training Institute and Department of Nephrology, Lapeyronie University Hospital, CHU Montpellier, 371 Avenue du Doyen G. Giraud, 34295 Montpellier, France. katja_martin@usa.net

Advances in Renal Replacement Therapy
|July 25, 2003
PubMed

More Related Videos

Implementation of a Hyperbolic Vortex Plasma Reactor for the Removal of Micropollutants in Water06:35

Implementation of a Hyperbolic Vortex Plasma Reactor for the Removal of Micropollutants in Water

Published on: July 25, 2025

Biogas Purification through the use of a Microalgae-Bacterial System in Semi-Industrial High Rate Algal Ponds07:34

Biogas Purification through the use of a Microalgae-Bacterial System in Semi-Industrial High Rate Algal Ponds

Published on: March 22, 2024

Related Concept Videos

Bioreactor Design and Operational System01:29

Bioreactor Design and Operational System

Bioreactors are engineered vessels designed to cultivate microorganisms under controlled conditions for industrial bioprocessing. They maintain sterility and allow precise regulation of pH, temperature, oxygen, and nutrient levels to optimize microbial growth and metabolite production. Bioreactors range from small laboratory units of 1 liter to industrial systems holding up to 500,000 liters, though only about 75% of their volume is actively used for fermentation. The remaining headspace...
Biological Treatment of Effluent and Waste Water01:30

Biological Treatment of Effluent and Waste Water

Biological wastewater treatment relies on the metabolic activity of microorganisms to remove pollutants from sewage. In modern treatment systems, this process is organized into sequential stages that progressively reduce solid material, dissolved organic matter, and microbial contamination. Each stage plays a distinct role in improving water quality and preparing the effluent for safe discharge or reuse.Primary and Secondary TreatmentPrimary treatment is a physical process that removes large...
Design Example: Designing a Residential Plumbing System01:25

Design Example: Designing a Residential Plumbing System

The design of residential plumbing systems requires carefully evaluating water demand, flow rates, and pressure dynamics to ensure both efficiency and reliability. The nature of water flow within pipes is defined by its Reynolds number, which classifies flow as either laminar (smooth) or turbulent.
Bioreactor Controls-I01:28

Bioreactor Controls-I

Maintaining optimal conditions within fermenters is essential for maximizing microbial productivity and ensuring process efficiency. This lesson focuses on key parameters—temperature, foam, pH, carbon dioxide, oxygen, and pressure—and their precise measurement and control strategies in fermentation systems.Temperature ControlTemperature regulation is critical due to the exothermic nature of many fermentation processes. In small laboratory fermenters, temperature is commonly monitored using...
Quality of Water01:19

Quality of Water

In concrete preparation, the quality of water is paramount as it affects the strength and durability of the concrete. Potable water is usually preferred; however, it must not have excessive sodium or potassium to prevent compromising the concrete's integrity. Water quality is typically evaluated based on impurities such as dissolved solids, chlorides, and sulfates, and its pH value is ideally between 6 and 8. Even slightly acidic natural water may be acceptable unless it contains harmful...
Testing Water Quality01:14

Testing Water Quality

When the quality of water for concrete preparation is uncertain, its impact on the setting time of cement and compressive strength of mortar is assessed by comparison with de-ionized or distilled water benchmarks. American Society for Testing and Materials (ASTM) C1602 requires the setting times to be within 90 minutes of the control, British Standard (BS) 3146:1980 allows a 30-minute variance in the initial setting, while British Standards European Norm (BS EN) 1008 specifies initial setting...