Related Experiment Video

Updated: Aug 10, 2026

Fabrication And Characterization Of Photonic Crystal Slow Light Waveguides And Cavities
11:08

Fabrication And Characterization Of Photonic Crystal Slow Light Waveguides And Cavities

Published on: November 30, 2012

Influence of planar cracks in plates on reflected and transmitted fields of Gaussian acoustic beams

J Vandeputte1, O Leroy, G Shkerdin

  • 1Interdisciplinary Research Center, K. U. Leuven Campus Kortrijk, B-8500 Kortrijk, Belgium.

The Journal of the Acoustical Society of America
|August 29, 2003
PubMed

More Related Videos

Conducting Elevated Temperature Normal and Combined Pressure-Shear Plate Impact Experiments Via a Breech-end Sabot Heater System10:52

Conducting Elevated Temperature Normal and Combined Pressure-Shear Plate Impact Experiments Via a Breech-end Sabot Heater System

Published on: August 7, 2018

Measurement of Chladni Mode Shapes with an Optical Lever Method04:39

Measurement of Chladni Mode Shapes with an Optical Lever Method

Published on: June 5, 2020

Related Concept Videos

Interference and Diffraction02:18

Interference and Diffraction

Interference is a characteristic phenomenon exhibited by waves. When two electromagnetic waves interact with their peaks and troughs coinciding, a resulting wave with enhanced amplitude is produced. This is known as constructive interference. In this case, the two waves interacting are in phase with each other.
Propagation of Waves01:07

Propagation of Waves

When a wave propagates from one medium to another, part of it may get reflected in the first medium, and part of it may get transmitted to the second medium. In such a case, the interface of the two mediums can be considered as a boundary that is neither fixed nor free.
Consider a scenario where a wave propagates from a string of low linear mass density to a string of high linear mass density. In such a case, the reflected wave is out of phase with respect to the incident wave, however the...
Gauss's Law: Planar Symmetry01:27

Gauss's Law: Planar Symmetry

A planar symmetry of charge density is obtained when charges are uniformly spread over a large flat surface. In planar symmetry, all points in a plane parallel to the plane of charge are identical with respect to the charges. Suppose the plane of the charge distribution is the xy-plane, and the electric field at a space point P with coordinates (x, y, z) is to be determined. Since the charge density is the same at all (x, y) - coordinates in the z = 0 plane, by symmetry, the electric field at P...
Distribution of Stresses in a Narrow Rectangular Beam01:11

Distribution of Stresses in a Narrow Rectangular Beam

In studying beam stress distribution, examining an elemental section is essential. To determine the average shearing stress on this face, the calculated shear is divided by the surface area. Importantly, shearing stresses on the beam's transverse and horizontal planes mirror each other, indicating a consistent stress distribution along the upper region of the beam. Notably, shearing stresses are absent at the beam's upper and lower surfaces due to the absence of applied forces in these areas.
Shearing Stresses in a Beam: Problem Solving01:14

Shearing Stresses in a Beam: Problem Solving

A cantilever beam with a rectangular cross-section under distributed and point loads experiences shearing stresses. The analysis begins by identifying the loads acting on the beam. Then, the reactions at the beam's fixed end are calculated using equilibrium equations. The vertical reaction is a combination of the distributed and point loads, while the moment reaction is the sum of their moments. The shear force distribution along the beam, resulting from these loads, is established by creating...
Principal Stresses in a Beam01:11

Principal Stresses in a Beam

In prismatic beams subject to arbitrary transverse loading, It is essential to analyze the interaction between shear forces and bending moments in order to understand stress distribution and ensure structural integrity. The highest normal or bending stress occurs at the outer fibers of the beam, decreasing linearly to zero at the neutral axis. In contrast, shear stress peaks at the neutral axis and diminishes toward the outer surfaces.
Analyzing principal stresses is crucial, especially in...