Related Experiment Video

Updated: Aug 29, 2026

Automation of Mode Locking in a Nonlinear Polarization Rotation Fiber Laser through Output Polarization Measurements
14:18

Automation of Mode Locking in a Nonlinear Polarization Rotation Fiber Laser through Output Polarization Measurements

Published on: February 28, 2016

Molding and stretched evolution of optical solitons in cumulative nonlinearities

Cesare Dari-Salisburgo1, Eugenio DelRe, Elia Palange

  • 1Dipartimento di Fisica, Università dell'Aquila, 67010 L'Aquila, Italy.

Physical Review Letters
|February 3, 2004
PubMed

More Related Videos

Transmission of Multiple Signals through an Optical Fiber Using Wavefront Shaping09:43

Transmission of Multiple Signals through an Optical Fiber Using Wavefront Shaping

Published on: March 20, 2017

Stimulated Stokes and Antistokes Raman Scattering in Microspherical Whispering Gallery Mode Resonators12:21

Stimulated Stokes and Antistokes Raman Scattering in Microspherical Whispering Gallery Mode Resonators

Published on: April 4, 2016

Related Concept Videos

Limits with Oscillating Discontinuities01:19

Limits with Oscillating Discontinuities

An oscillating discontinuity is a type of discontinuity in which a function’s values fluctuate infinitely often as the input approaches a particular point. Unlike jump discontinuities, where the function suddenly shifts between two values, or infinite discontinuities, where the function diverges without bound, an oscillating discontinuity arises from rapid back-and-forth variation. Because the function never stabilizes toward a single value, no finite limit exists at that point.One of the most...
Plastic Deformation in Circular Shafts01:20

Plastic Deformation in Circular Shafts

When materials are subjected to forces that surpass their yield strength, they undergo a process known as plastic deformation. This results in a permanent alteration or strain in their structure. This concept can be specifically applied to circular shafts, where the deformation leads to a change in its shape. The precise evaluation of this plastic deformation requires understanding the stress distribution within the circular shaft, which is achieved by calculating the maximum shearing stress in...
Deformations in a Transverse Cross Section01:21

Deformations in a Transverse Cross Section

When a material is subjected to uniaxial stress, it elongates or contracts in the direction of the applied force, and also undergoes changes in the perpendicular directions. This behavior is crucial for understanding how materials behave under stress and is governed by mechanical properties such as Poisson's ratio v, which measures the ratio of transverse strain to axial strain.
As the material stretches, it expands or contracts in orthogonal directions to the load. This phenomenon varies...
Divergence and Stokes' Theorems01:06

Divergence and Stokes' Theorems

The divergence and Stokes' theorems are a variation of Green's theorem in a higher dimension. They are also a generalization of the fundamental theorem of calculus. The divergence theorem and Stokes' theorem are in a way similar to each other; The divergence theorem relates to the dot product of a vector, while Stokes' theorem relates to the curl of a vector. Many applications in physics and engineering make use of the divergence and Stokes' theorems, enabling us to write numerous physical laws...
Boundary Conditions: Lossless Lines01:21

Boundary Conditions: Lossless Lines

Consider a single-phase, two-wire, lossless transmission line terminated by an impedance at the receiving end and a source with Thevenin voltage and impedance at the sending end. The line, with length, has a surge impedance and wave velocity determined by the line's inductance and capacitance.
At the receiving end, the boundary condition states that the voltage equals the product of the receiving-end impedance and current. This relationship is expressed as a function of the incident and...
Relation between Poisson's ratio, Modulus of Elasticity and Modulus of Rigidity01:15

Relation between Poisson's ratio, Modulus of Elasticity and Modulus of Rigidity

Deformation occurs in axial and transverse directions when an axial load is applied to a slender bar. This deformation impacts the cubic element within the bar, transforming it into either a rectangular parallelepiped or a rhombus, contingent on its orientation. This transformation process induces shearing strain. Axial loading elicits both shearing and normal strains. Applying an axial load instigates equal normal and shearing stresses on elements oriented at a 45° angle to the load axis.