Related Experiment Video

Updated: Aug 26, 2026

Atomic Force Microscopy Cantilever-Based Nanoindentation: Mechanical Property Measurements at the Nanoscale in Air and Fluid
08:58

Atomic Force Microscopy Cantilever-Based Nanoindentation: Mechanical Property Measurements at the Nanoscale in Air and Fluid

Published on: December 2, 2022

Young's modulus of sections of living branches and tree trunks

M G Cannell1, J Morgan

  • 1Institute of Terrestrial Ecology, Bush Estate, Penicuik, Midlothian EH26 0QB, Scotland.

Tree Physiology
|December 1, 1987
PubMed

More Related Videos

AFM-based Mapping of the Elastic Properties of Cell Walls: at Tissue, Cellular, and Subcellular Resolutions10:26

AFM-based Mapping of the Elastic Properties of Cell Walls: at Tissue, Cellular, and Subcellular Resolutions

Published on: July 24, 2014

Tree Core Analysis with X-ray Computed Tomography06:56

Tree Core Analysis with X-ray Computed Tomography

Published on: September 22, 2023

Related Concept Videos

Indeterminate Structure01:18

Indeterminate Structure

Indeterminate structures refer to structures where internal forces and reactions cannot be determined using only the equations of static equilibrium.  Indeterminate structures have more unknown forces and reaction forces than equations of static equilibrium that can be used to determine them. Indeterminate structures are often used in engineering to create complex, efficient, and aesthetically pleasing structures. There are various types of indeterminate structures used in engineering and some...
Strain and Elastic Modulus01:15

Strain and Elastic Modulus

The quantity that describes the deformation of a body under stress is known as strain. Strain is given as a fractional change in either length, volume, or geometry under tensile, volume (also known as bulk), or shear stress, respectively, and is a dimensionless quantity. The strain experienced by a body under tensile or compressive stress is called tensile or compressive strain, respectively. In contrast, the strain experienced under bulk stress and shear stress is known as volume and shear...
Bending of Members Made of Several Materials01:11

Bending of Members Made of Several Materials

In analyzing a structural member composed of two different materials with identical cross-sectional areas, it is crucial to understand how their distinct elastic properties affect the member's response under load. The analysis involves assessing stress and strain distributions using the transformed section concept, which accounts for variations in material properties.
Hooke's Law determines stress in each material, stating that stress is proportional to strain but varies due to each material's...
Structural Properties and Dimensions of Lumber01:21

Structural Properties and Dimensions of Lumber

Wood's structural properties derive from fibers aligned along the tree's length, contributing significantly to its mechanical strength. Wood exhibits up to twenty times greater tensile strength along these fibers compared to across them, and generally shows better performance under compression than tension. The length of fibers varies, with hardwoods having fibers around one twenty-fifth inch long and softwoods ranging from one-eighth to one-third inch.
The strength characteristics of wood are...
Introduction to Wood01:19

Introduction to Wood

Wood, derived from trees, is a versatile and widely used construction material. Trees feature a trunk surrounded by a protective layer of dead bark. Beneath this outer layer lies the living bark, followed by the cambium, and then the sapwood which transitions into heartwood as it matures. At the center of the trunk is the pith. The age of a tree can be discerned by examining its growth rings, which are concentric bands visible in the trunk's cross-section.
The structural integrity of the wood...
Normal Strain under Axial Loading01:20

Normal Strain under Axial Loading

Normal strain under axial loading is an important concept in the field of mechanics of materials. Axial loading implies the application of a force along the axis of a material, like a column or bar. This force can either compress or stretch the material. In the context of axial loading, normal strain is the deformation experienced by the material in the direction of the loading force. It's calculated as the change in length divided by the original length of the material. This unitless ratio...