Related Experiment Video

Updated: Aug 6, 2026

Cooling an Optically Trapped Ultracold Fermi Gas by Periodical Driving
11:21

Cooling an Optically Trapped Ultracold Fermi Gas by Periodical Driving

Published on: March 30, 2017

Evaporative cooling of helium nanodroplets with angular momentum conservation

Kevin K Lehmann1, Adriaan M Dokter

  • 1Department of Chemistry, Princeton University, Princeton, NJ 08544, USA. lehmann@princeton.edu

Physical Review Letters
|June 1, 2004
PubMed

More Related Videos

Cryogenic Liquid Jets for High Repetition Rate Discovery Science08:34

Cryogenic Liquid Jets for High Repetition Rate Discovery Science

Published on: May 9, 2020

Optimization of An Air-Based Heat Management System for Dusty Particulate Matter-Covered Lithium-Ion Battery Packs10:36

Optimization of An Air-Based Heat Management System for Dusty Particulate Matter-Covered Lithium-Ion Battery Packs

Published on: November 3, 2023

Related Concept Videos

Phase Transitions: Vaporization and Condensation02:39

Phase Transitions: Vaporization and Condensation

The physical form of a substance changes on changing its temperature. For example, raising the temperature of a liquid causes the liquid to vaporize (convert into vapor). The process is called vaporization—a surface phenomenon. Vaporization occurs when the thermal motion of the molecules overcome the intermolecular forces, and the molecules (at the surface) escape into the gaseous state. When a liquid vaporizes in a closed container, gas molecules cannot escape. As these gas phase molecules...
Conservation of Angular Momentum01:09

Conservation of Angular Momentum

A system's total angular momentum remains constant if the net external torque acting on the system is zero. Considering a system that consists of n tiny particles, the angular momentum of any tiny particle may change, but the system's total angular momentum would remain constant. The principle of conservation of angular momentum only considers the net external torque acting on the system. While there are internal forces exerted by different particles within the system that also produce internal...
Heat Capacities of an Ideal Gas I01:14

Heat Capacities of an Ideal Gas I

Heat capacity is the ratio of heat absorbed by the substance corresponding to its temperature change. It is also called thermal capacity and the SI unit of heat capacity is J/K. Whereas, specific heat capacity is defined as the amount of heat necessary to change the temperature of 1 kg of a substance by 1 K and is also called massic heat capacity. Its SI unit is J/kg⋅K.
Molar heat capacity quantifies the ratio of the amount of heat added (or removed) to increase (or decrease) the temperature of...
Heat Capacities of an Ideal Gas II01:23

Heat Capacities of an Ideal Gas II

For a system that undergoes a thermodynamic process at a constant volume condition, the heat absorbed is used only to increase the system's internal energy and not for doing any kind of work. While for a system undergoing a thermodynamic process under a constant pressure condition, the amount of heat absorbed is used not only for increasing the internal energy (as a function of temperature) but also for doing some work. The molar heat capacity is the amount of heat required to increase the...
Heat Capacities of an Ideal Gas III01:25

Heat Capacities of an Ideal Gas III

The number of independent ways a gas molecule can move along straight line, rotate, and vibrate is called its degrees of freedom. Supposing d represents the number of degrees of freedom of an ideal gas, the molar heat capacity at constant volume of an ideal gas in terms of d is
Adiabatic Processes for an Ideal Gas01:18

Adiabatic Processes for an Ideal Gas

When an ideal gas is compressed adiabatically, that is, without adding heat, work is done on it, and its temperature increases. In an adiabatic expansion, the gas does work, and its temperature drops. Adiabatic compressions actually occur in the cylinders of a car, where the compressions of the gas-air mixture take place so quickly that there is no time for the mixture to exchange heat with its environment. Nevertheless, because work is done on the mixture during the compression, its...