Related Experiment Video

Updated: Aug 22, 2026

An Experimental and Finite Element Protocol to Investigate the Transport of Neutral and Charged Solutes across Articular Cartilage
07:57

An Experimental and Finite Element Protocol to Investigate the Transport of Neutral and Charged Solutes across Articular Cartilage

Published on: April 23, 2017

Correlation of T1rho with fixed charge density in cartilage

Andrew J Wheaton1, Francis L Casey, Alexander J Gougoutas

  • 1Department of Radiology, University of Pennsylvania, Philadelphia, USA. wheaton@seas.upenn.edu

Journal of Magnetic Resonance Imaging : JMRI
|August 28, 2004
PubMed
Abstract

More Related Videos

Characterization of Intra-Cartilage Transport Properties of Cationic Peptide Carriers09:02

Characterization of Intra-Cartilage Transport Properties of Cationic Peptide Carriers

Published on: August 10, 2020

Atomic Force Microscopy Measurements of Cartilage in Intact and Regenerating Axolotl Limbs09:19

Atomic Force Microscopy Measurements of Cartilage in Intact and Regenerating Axolotl Limbs

Published on: October 11, 2024

Related Concept Videos

Growth of Cartilage and Bone Tissue01:27

Growth of Cartilage and Bone Tissue

Chondrocytes form a temporary cartilaginous model by dividing and secreting a thick gel-like extracellular matrix. Once the chondrocytes undergo programmed cell death, osteoblasts enter the site of the cartilaginous model. The process of replacing the temporary cartilaginous model with bone in an ordered manner is called endochondral ossification. In endochondral ossification, not all of the cartilage is replaced by bone tissue. Some cartilage that performs a protective and supportive function...
Boundary Conditions for Current Density01:25

Boundary Conditions for Current Density

Current density becomes discontinuous across an interface of materials with different electrical conductivities. The normal component of the current density is continuous across the boundary.
Relation between Poisson's ratio, Modulus of Elasticity and Modulus of Rigidity01:15

Relation between Poisson's ratio, Modulus of Elasticity and Modulus of Rigidity

Deformation occurs in axial and transverse directions when an axial load is applied to a slender bar. This deformation impacts the cubic element within the bar, transforming it into either a rectangular parallelepiped or a rhombus, contingent on its orientation. This transformation process induces shearing strain. Axial loading elicits both shearing and normal strains. Applying an axial load instigates equal normal and shearing stresses on elements oriented at a 45° angle to the load axis.
Thin-Walled Hollow Shafts01:15

Thin-Walled Hollow Shafts

In analyzing a thin-walled hollow shaft subjected to torsional loading, a segment with width dx is isolated for examination. Despite its equilibrium state, this segment faces torsional shearing forces at its ends. These forces are quantitatively described by the product of the longitudinal shearing stress on the segment's minor surface and the area of this surface, leading to the concept of shear flow. This shear flow is consistent throughout the structure, indicating a uniform distribution of...
Resistivity01:22

Resistivity

When a voltage is applied to a conductor, an electrical field is generated, and charges in the conductor feel the force due to the electrical field. The current density that results depends on the electrical field and the properties of the material. In some materials, including metals at a given temperature, the current density is approximately proportional to the electrical field. In these cases, the current density can be modeled as:
Circular Shaft - Stresses in Linear Range01:13

Circular Shaft - Stresses in Linear Range

Consider a scenario where a circular shaft is subject to torque that remains within the boundaries of Hooke's Law, avoiding any permanent deformation. So, the formula for shearing strain is revisited. This formula is multiplied by the modulus of rigidity, and then Hooke's Law for the shearing stress and strain is applied. As a result, the equation for shearing stress in a shaft can be derived.