Related Experiment Video

Updated: Aug 19, 2026

Setup for the Quantitative Assessment of Motion and Muscle Activity During a Virtual Modified Box and Block Test
04:06

Setup for the Quantitative Assessment of Motion and Muscle Activity During a Virtual Modified Box and Block Test

Published on: January 12, 2024

Correlation between wrist loads and the distal radius volar tilt angle

Ioannis A Karnezis1

  • 1Department of Orthopaedic Surgery, University of Bristol, Bristol BS2 8HW, UK. mail@ioanniskarnezis.gr

Clinical Biomechanics (Bristol, Avon)
|February 9, 2005
PubMed
Abstract

Related Concept Videos

Bones of the Upper Limb: Radius01:09

Bones of the Upper Limb: Radius

The radius is longer of the two bones that make up the human antebrachium or forearm. At the proximal end, the radius articulates with the capitulum of the humerus and the radial notch of the ulna to form the elbow joint. At the distal end, the radius articulates with the ulna via the ulnar notch, forming the distal radioulnar joint. Distally, the radius also attaches to the carpal wrist bones (scaphoid and lunate) to form the radiocarpal joint.
The radius has a nail-shaped head, and a short...
Bones of the Upper Limb: Ulna01:15

Bones of the Upper Limb: Ulna

The ulna and radius are parallel bones of the antebrachium or the forearm. The ulna lies medially and consists of a bony tip called the olecranon process at its proximal end. This hook-like projection articulates with the olecranon fossa of the humerus and forms the "hinged" ulnohumeral part of the elbow joint. This joint facilitates forearm extension and flexion while preventing its hyperextension. Similarly, the coronoid process, another bony projection on the proximal/anterior side of the...
Angle of Twist - Elastic Range01:13

Angle of Twist - Elastic Range

Consider a cylindrical shaft with a length denoted by L and a consistent cross-sectional radius referred to as r. This shaft undergoes a torque at the free end. The highest shearing strain within the shaft is directly proportional to the twist angle and the radial distance from the shaft axis. When the shaft behaves elastically, this shearing strain can be articulated using variables such as the applied torque, radial distance, the polar moment of inertia, and the modulus of rigidity. By...
Residual Stresses in Circular Shafts01:10

Residual Stresses in Circular Shafts

In materials that exhibit elastic and plastic behavior, known as elastoplastic materials, residual stresses can accumulate when these materials experience plastic deformation. This deformation arises from either high levels of shearing stress or significant strains. Residual stresses are internal stresses that persist within a material after removing the external force causing deformation. This phenomenon is demonstrated when observing the behavior of a shaft under torque; notably, the shaft's...
Angle of Twist: Problem Solving01:13

Angle of Twist: Problem Solving

An electric motor applies a torque of 700 N·m to an aluminum shaft, triggering a stable rotation. Two pulleys, B and C, are subjected to torques of 300 N·m and 400 N·m, respectively. The modulus of rigidity is provided as 25 GPa. With the knowledge of the length and diameter of each segment, the twist angle between the two pulleys can be computed. First, a section cut is made between pulleys B and C, and the cut cross-section is analyzed using a free-body diagram. Given that the torque exerted...
Deformation in a Circular Shaft01:10

Deformation in a Circular Shaft

One of the distinctive characteristics of circular shafts is their ability to maintain their cross-sectional integrity under torsion. In other words, each cross-section continues to exist as a flat, unaltered entity, simply rotating like a solid, rigid slab. To understand the distribution of shearing stress within such a shaft, consider a cylindrical section inside this circular shaft. This section has a length of L and a radius of R, with one end fixed. The radius of the cylindrical section is...