Related Experiment Video

Updated: Jul 9, 2026

Method to Measure Tone of Axial and Proximal Muscle
10:41

Method to Measure Tone of Axial and Proximal Muscle

Published on: December 14, 2011

Turn and helical peptide handedness governed exclusively by side-chain chiral centers

Soledad Royo1, Wim M De Borggraeve, Cristina Peggion

  • 1Department of Organic Chemistry, ICMA, University of Zaragoza-CSIC, 50009 Zaragoza, Spain.

Journal of the American Chemical Society
|February 17, 2005
PubMed

More Related Videos

Magnetic Tweezers for the Measurement of Twist and Torque11:41

Magnetic Tweezers for the Measurement of Twist and Torque

Published on: May 19, 2014

Operation of the Collaborative Composite Manufacturing (CCM) System10:09

Operation of the Collaborative Composite Manufacturing (CCM) System

Published on: October 1, 2019

Related Concept Videos

Gyroscope01:02

Gyroscope

A gyroscope is defined as a spinning disk in which the axis of rotation is free to assume any orientation. When spinning, the orientation of the spin axis is unaffected by the orientation of the body that encloses it. The body or vehicle enclosing the gyroscope can be moved from place to place, while the orientation of the spin axis remains the same. This makes gyroscopes very useful in navigation, especially where magnetic compasses cannot be used, such as in crewed and crewless spacecraft,...
Gyroscope: Precession01:24

Gyroscope: Precession

Precession can be demonstrated effectively through a spinning top. If a spinning top is placed on a flat surface near the surface of the Earth at a vertical angle and is not spinning, it will fall over due to the force of gravity producing a torque acting on its center of mass. However, if the top is spinning on its axis, it precesses about the vertical direction, rather than topple over due to this torque. Precessional motion is a combination of a steady circular motion of the axis and the...
Mechanism of Ciliary Motion01:05

Mechanism of Ciliary Motion

The ciliary structures were first seen in 1647 by Antonie Leeuwenhoek while observing the protozoans. In lower organisms, these appendages are responsible for cell movement, while in higher organisms, these appendages help in the movement of the extracellular fluids within the body cavities.
The cilia are made up of microtubules in a 9+2 arrangement, with nine microtubule doublet ring bundles, surrounding a pair of central singlet microtubule bundles. The doublet microtubule bundles are...
Rotational Motion about a Fixed Axis01:26

Rotational Motion about a Fixed Axis

A rigid body's rotation around a fixed axis makes every point within it trace a circular path around a specific line or point. The term given to this type of spinning is defined by the angular position, symbolized by the angle θ. This angle is gauged from a static reference line to the revolving object. From this angular position, any variation is referred to as angular displacement, denoted by dθ. The extent of this displacement can be calculated in degrees, radians, or revolutions, where one...
Equation of Motion: Rotation About a Fixed Axis01:18

Equation of Motion: Rotation About a Fixed Axis

Consider a flywheel, having an uneven mass distribution, rotating steadily around a fixed axis. As this rotation occurs, the center of mass of the flywheel traces a circular path. Understanding the acceleration of this center of mass requires observing both its tangential and normal components.
The tangential component is dependent on the direction of the angular acceleration of the flywheel. The tangential component of the acceleration propels the flywheel along its path. On the other hand,...
Angle of Twist: Problem Solving01:13

Angle of Twist: Problem Solving

An electric motor applies a torque of 700 N·m to an aluminum shaft, triggering a stable rotation. Two pulleys, B and C, are subjected to torques of 300 N·m and 400 N·m, respectively. The modulus of rigidity is provided as 25 GPa. With the knowledge of the length and diameter of each segment, the twist angle between the two pulleys can be computed. First, a section cut is made between pulleys B and C, and the cut cross-section is analyzed using a free-body diagram. Given that the torque exerted...