Related Experiment Video

Updated: Aug 19, 2026

Setup of Capillary Electrophoresis-Inductively Coupled Plasma Mass Spectrometry (CE-ICP-MS) for Quantification of Iron Redox Species (Fe(II), Fe(III))
04:48

Setup of Capillary Electrophoresis-Inductively Coupled Plasma Mass Spectrometry (CE-ICP-MS) for Quantification of Iron Redox Species (Fe(II), Fe(III))

Published on: May 4, 2020

Effect of base addition rate on the preparation of partially neutralized ferric chloride solutions

Ta-Kang Liu1, Edward S K Chian

  • 1School of Civil and Environmental Engineering, Georgia Institute of Technology, 311 Ferst Drive, Atlanta, GA 30332, USA. tkliu@thl.ncku.edu.tw

Journal of Colloid and Interface Science
|March 23, 2005
PubMed

More Related Videos

Quantifiable and Inexpensive Cell-Free Fluorescent Method to Confirm the Ability of Novel Compounds to Chelate Iron05:36

Quantifiable and Inexpensive Cell-Free Fluorescent Method to Confirm the Ability of Novel Compounds to Chelate Iron

Published on: February 23, 2024

Synthesis of Cationized Magnetoferritin for Ultra-fast Magnetization of Cells10:23

Synthesis of Cationized Magnetoferritin for Ultra-fast Magnetization of Cells

Published on: December 13, 2016

Related Concept Videos

Titration of a Strong Acid with a Strong Base01:23

Titration of a Strong Acid with a Strong Base

During the titration of a strong acid with a strong base, pH calculations are primarily based on the concentration of residual hydronium or hydroxide ions. Initially, a strong acid like hydrochloric acid fully dissociates, creating hydronium and chloride ions, resulting in a low pH. The addition of a strong base like sodium hydroxide alters the concentration of hydronium ions by neutralizing them. As more base is added, the pH gradually increases. At the equivalence point, all hydronium ions...
Calculating pH Changes in a Buffer Solution02:45

Calculating pH Changes in a Buffer Solution

A buffer can prevent a sudden drop or increase in the pH of a solution after the addition of a strong acid or base up to its buffering capacity; however, such addition of a strong acid or base does result in the slight pH change of the solution. The small pH change can be calculated by determining the resulting change in the concentration of buffer components, i.e., a weak acid and its conjugate base or vice versa. The concentrations obtained using these stoichiometric calculations can be used...
Titration Calculations: Strong Acid - Strong Base02:28

Titration Calculations: Strong Acid - Strong Base

Calculating pH for Titration Solutions: Strong Acid/Strong Base
A titration is carried out for 25.00 mL of 0.100 M HCl (strong acid) with 0.100 M of a strong base NaOH. The pH at different volumes of added base solution can be calculated as follows:
(a) Titrant volume = 0 mL. The solution pH is due to the acid ionization of HCl. Because this is a strong acid, the ionization is complete and the hydronium ion molarity is 0.100 M. The pH of the solution is then:
EDTA: Auxiliary Complexing Reagents01:26

EDTA: Auxiliary Complexing Reagents

EDTA titrations are usually carried out in highly basic conditions, where the fully deprotonated form of EDTA, Y4−, actively complexes with the free metal ions in the solution. Several metal ions precipitate as hydrous oxide (hydroxides, oxides, or oxyhydroxides) under these conditions, lowering the concentration of free metal ions in the solution. For this reason, auxiliary complexing agents or ligands such as ammonia, tartrate, citrate, or triethanolamine are used in EDTA titrations to...
Titration of a Weak Base with a Strong Acid01:20

Titration of a Weak Base with a Strong Acid

The titration curve of a weak base like ammonia with a strong acid like hydrochloric acid is the mirror image of the titration curve of a weak acid with a strong base.
Using the ICE table and substituting the Kb value, we calculate the initial pH of 50 mL of 0.1 M ammonia to be 11.11. Addition of 25 mL of 0.1 M hydrochloric acid to this solution of ammonia results in a buffer with an equal concentration of ammonia and ammonium ions. The pH of this buffer can be calculated by substituting these...
Formation of Complex Ions03:45

Formation of Complex Ions

A type of Lewis acid-base chemistry involves the formation of a complex ion (or a coordination complex) comprising a central atom, typically a transition metal cation, surrounded by ions or molecules called ligands. These ligands can be neutral molecules like H2O or NH3, or ions such as CN− or OH−. Often, the ligands act as Lewis bases, donating a pair of electrons to the central atom. These types of Lewis acid-base reactions are examples of a broad subdiscipline called coordination...