[Carving skiing]

Related Experiment Video

Updated: Aug 18, 2026

Rendering SiO2/Si Surfaces Omniphobic by Carving Gas-Entrapping Microtextures Comprising Reentrant and Doubly Reentrant Cavities or Pillars
08:02

Rendering SiO2/Si Surfaces Omniphobic by Carving Gas-Entrapping Microtextures Comprising Reentrant and Doubly Reentrant Cavities or Pillars

Published on: February 11, 2020

H Hörterer1

  • 1Abteilung Orthopädie und Sportmedizin, Medical Park Bad Wiessee -- St. Hubertus. h.hoerterer@medicalpark-sthubertus.de

Der Orthopade
|April 28, 2005
PubMed

More Related Videos

Scaled Anatomical Model Creation of Biomedical Tomographic Imaging Data and Associated Labels for Subsequent Sub-surface Laser Engraving (SSLE) of Glass Crystals07:57

Scaled Anatomical Model Creation of Biomedical Tomographic Imaging Data and Associated Labels for Subsequent Sub-surface Laser Engraving (SSLE) of Glass Crystals

Published on: April 25, 2017

Measuring the Complete-arch Distortion of an Optical Dental Impression06:51

Measuring the Complete-arch Distortion of an Optical Dental Impression

Published on: May 30, 2019

Related Concept Videos

Wood Surfacing01:14

Wood Surfacing

Wood surfacing is a critical finishing process designed to smoothen the wood surface, enhance its dimensional accuracy, and make handling safer. This process compensates for potential shrinkage during the seasoning phase by marginally increasing the wood dimensions before surfacing. It also helps correct some distortions that may occur as the wood dries.
The equipment used in the surfacing process is a plane equipped with rotating blades. This tool efficiently smoothens the wood surface and can...
Carbon Skeletons01:12

Carbon Skeletons

Life on Earth is carbon-based, as all macromolecules that make up living organisms contain carbon atoms. All organic compounds have a carbon backbone. Each carbon atom is tetravalent and can bond with four other atoms, making it an extraordinarily flexible component of biological molecules. Because carbon’s valence electrons are stable, it rarely becomes an ion. As the carbon chain increases in length, structural modifications such as ring structures, double bonds, and branching side chains...
Elevation of Intermediate Points on Vertical Curves01:20

Elevation of Intermediate Points on Vertical Curves

Vertical curves are essential in roadway design because they provide smooth transitions between varying roadway grades. Designing vertical curves involves calculating intermediate elevations and identifying the curve's highest or lowest point, which is essential for optimal roadway performance.Intermediate elevations on a vertical curve are determined using the tangent offset method. This method considers the initial elevation at the start of the curve, the grades, and the curve's geometry. The...
Parametric Surfaces01:30

Parametric Surfaces

A parametric surface in three-dimensional space is defined through a vector-valued function\begin{equation*}\mathbf{r}(u, v) = x(u, v)\mathbf{i} + y(u, v)\mathbf{j} + z(u, v)\mathbf{k}\end{equation*}where u and v are parameters within a specified domain D in the uv-plane. The functions x(u, v), y(u, v), and z(u, v) define the coordinates of points on the surface. As u and v vary over D, the position vector r(u, v) traces a continuous surface in space. This parametric representation is essential...
Adjusting a Traverse01:12

Adjusting a Traverse

In the site survey of a four-sided traverse, internal angles are essential to ensure geometric accuracy. The survey revealed that the sum of the measured internal angles was 359 degrees and 48 minutes, which is 12 minutes less than the expected 360 degrees. This discrepancy signals an error likely arising from measurement inaccuracies during the fieldwork.To rectify this error, the adjustment process involved distributing the 12-minute shortfall equally across the four internal angles. By...
Veneer01:19

Veneer

Veneer refers to a thin sheet of wood, typically produced to a thickness of about one-eighth of an inch or less. This material is crafted through various methods, the most common being rotary cutting. In this process, a log is mounted into a large lathe and spun against a knife edge, peeling off a continuous strip of wood as the knife penetrates deeper into the rotating log, creating a rotary-cut veneer.
Other veneering techniques include plain-slicing, quarter-slicing, and rift-slicing. These...