Related Experiment Video

Updated: Aug 18, 2026

Orientational Transition in a Liquid Crystal Triggered by the Thermodynamic Growth of Interfacial Wetting Sheets
06:26

Orientational Transition in a Liquid Crystal Triggered by the Thermodynamic Growth of Interfacial Wetting Sheets

Published on: May 15, 2017

Calorimetric investigations of liquid-crystal compounds exhibiting almost no layer-shrinkage behavior through the

K Ema1, K Takekoshi, H Yao

  • 1Department of Physics, Graduate School of Science and Engineering, Tokyo Institute of Technology, Meguro, Japan. kema@phys.titech.ac.jp

Physical Review. E, Statistical, Nonlinear, and Soft Matter Physics
|May 21, 2005
PubMed

More Related Videos

Measuring Magnetically-Tuned Ferroelectric Polarization in Liquid Crystals07:03

Measuring Magnetically-Tuned Ferroelectric Polarization in Liquid Crystals

Published on: August 15, 2018

Novel Techniques for Observing Structural Dynamics of Photoresponsive Liquid Crystals10:35

Novel Techniques for Observing Structural Dynamics of Photoresponsive Liquid Crystals

Published on: May 29, 2018

Related Concept Videos

Solid–Solid Solutions01:24

Solid–Solid Solutions

The temperature-composition phase diagram of two solids, A and B, which are immiscible in the solid phase but form miscible liquids, shows that when the temperature is low, these two exist as separate, pure solids (A and B). As the temperature increases, they transition into a single-phase liquid solution where A and B coexist. Moving from point a1 to a2 in the phase diagram, the composition changes such that solid B begins to separate from the solution, enriching the remaining liquid with A.
Phase Transitions: Melting and Freezing02:39

Phase Transitions: Melting and Freezing

Heating a crystalline solid increases the average energy of its atoms, molecules, or ions, and the solid gets hotter. At some point, the added energy becomes large enough to partially overcome the forces holding the molecules or ions of the solid in their fixed positions, and the solid begins the process of transitioning to the liquid state or melting. At this point, the temperature of the solid stops rising, despite the continual input of heat, and it remains constant until all of the solid is...
Polymer Classification: Crystallinity01:21

Polymer Classification: Crystallinity

Unlike ionic or small covalent molecules, polymers do not form crystalline solids due to the diffusion limitations of their long-chain structures. However, polymers contain microscopic crystalline domains separated by amorphous domains.
Crystalline domains are the regions where polymer chains are aligned in an orderly manner and held together in proximity by intermolecular forces. For example, chains in the crystalline domains of polyethylene and nylon are bound together by van der Waals...
Recrystallization: Solid–Solution Equilibria01:10

Recrystallization: Solid–Solution Equilibria

Recrystallization is a purification technique used to separate impurities from solid compounds. In this technique, no chemical reactions occur. Instead, it exploits physical properties only, specifically, the solubility differences between the desired compound and impurities, either at a single temperature or at different temperatures, and under other selected conditions. The solid-solution equilibrium (solubility equilibrium) of each component in the solution represents a binary phase...
Two Components: Liquid–Liquid Systems01:27

Two Components: Liquid–Liquid Systems

A pressure-composition phase diagram explicitly describes the behavior of an ideal solution of two volatile liquids under varying pressures and compositions. A pressure-composition diagram has two main curves. The bubble point curve represents the plot of pressure versus liquid mole fraction. It indicates the pressure at which the first bubble of vapor forms from the liquid phase as the system pressure decreases.The dew point curve is the pressure versus vapor mole fraction. It indicates the...
Phase Transitions: Sublimation and Deposition02:33

Phase Transitions: Sublimation and Deposition

Some solids can transition directly into the gaseous state, bypassing the liquid state, via a process known as sublimation. At room temperature and standard pressure, a piece of dry ice (solid CO2) sublimes, appearing to gradually disappear without ever forming any liquid. Snow and ice sublimate at temperatures below the melting point of water, a slow process that may be accelerated by winds and the reduced atmospheric pressures at high altitudes. When solid iodine is warmed, the solid sublimes...