Related Experiment Video

Updated: Aug 15, 2026

Fabrication and Operation of a Nano-Optical Conveyor Belt
11:10

Fabrication and Operation of a Nano-Optical Conveyor Belt

Published on: August 26, 2015

Critical phenomenon of granular flow on a conveyor belt

Bao De-Song1, Zhang Xun-Sheng, Xu Guang-Lei

  • 1Department of Physics, Zhejiang University, Hangzhou, China. baodesong@mail.hz.zj.cn

Physical Review. E, Statistical, Nonlinear, and Soft Matter Physics
|October 26, 2005
PubMed

More Related Videos

An Analog Macroscopic Technique for Studying Molecular Hydrodynamic Processes in Dense Gases and Liquids11:03

An Analog Macroscopic Technique for Studying Molecular Hydrodynamic Processes in Dense Gases and Liquids

Published on: December 4, 2017

Visualization of Failure and the Associated Grain-Scale Mechanical Behavior of Granular Soils under Shear using Synchrotron X-Ray Micro-Tomography09:00

Visualization of Failure and the Associated Grain-Scale Mechanical Behavior of Granular Soils under Shear using Synchrotron X-Ray Micro-Tomography

Published on: September 29, 2019

Related Concept Videos

Frictional Forces on Flat Belts01:28

Frictional Forces on Flat Belts

Flat belts are commonly used in various industrial applications for transmitting power from one pulley to another. When a flat belt is wrapped around a set of pulleys, it experiences different tensions at the driving pulley ends due to the friction between the belt and pulley surface. When the pulley moves in a counterclockwise direction, the tension T2 on the opposite side of the pulley where the belt is moving away from is higher than the tension T1 on the side where the belt is moving...
Flat Belts: Problem Solving01:28

Flat Belts: Problem Solving

Flat belts are crucial in many industrial applications as they help transmit power from one pulley to another. The concept of forces and moments is used to determine the maximum moment on a pulley. For instance, consider a flat belt that wraps around two pulleys, A and B, with radii of 30 cm and 10 cm, respectively. The angle between the belt and the horizontal is 20 degrees at the pulleys. As pulley B rotates clockwise and drives pulley A, tension T2 is caused at one end of the belt, while...
Design Example: Aggregate Gradation01:24

Design Example: Aggregate Gradation

The right type and quality of aggregates are crucial for concrete as they significantly influence its properties, mix proportions, and cost-effectiveness. If different sources are available for sand, the commonly used fine aggregate in concrete, the selection of sand is primarily based on its gradation.
The grading, or particle-size distribution, of sand is determined using sieve analysis, with standard sizes ranging from 150 μm to 10 mm (ASTM No. 100 sieve to 3⁄8 in. sieve). Sand is sampled...
Couette Flow01:22

Couette Flow

Couette flow represents the flow of fluid between two parallel plates, with one plate fixed and the other moving with a constant velocity. This configuration allows for a simplified analysis using the Navier-Stokes equations, which govern fluid motion under conditions of viscosity and incompressibility. For Couette flow, the assumptions include a steady, laminar, incompressible flow with a zero-pressure gradient in the flow direction. This flow type is beneficial for understanding shear-driven...
Turbulent Flow01:24

Turbulent Flow

Turbulent flow is characterized by unpredictable fluctuations in velocity and pressure, which result in a chaotic fluid movement distinct from the orderly patterns of laminar flow. While laminar flow is governed by smooth, parallel layers with minimal mixing, turbulent flow exhibits highly irregular, three-dimensional patterns. This behavior arises due to instabilities in the fluid's velocity profile, and amplifies as the flow velocity increases. Minor disturbances, known as turbulent spots,...
Irrotational Flow01:28

Irrotational Flow

Irrotational flow is characterized by fluid motion where particles do not rotate around their axes, resulting in zero vorticity. For a flow to be irrotational, the curl of the velocity field must be zero. This imposes specific conditions on velocity gradients. For instance, to maintain zero rotation about the z-axis, the gradient condition: