Related Experiment Video

Updated: Aug 14, 2026

Investigating the Detrimental Effects of Low Pressure Plasma Sterilization on the Survival of Bacillus subtilis Spores Using Live Cell Microscopy
10:03

Investigating the Detrimental Effects of Low Pressure Plasma Sterilization on the Survival of Bacillus subtilis Spores Using Live Cell Microscopy

Published on: November 30, 2017

Effect of Sterilization by Dry Heat or Autoclaving on Bacterial Penetration through Berea Sandstone

G E Jenneman1, M J McInerney, M E Crocker

  • 1Department of Botany and Microbiology and School of Petroleum and Geological Engineering, University of Oklahoma, Norman, Oklahoma 73019, and National Institute for Petroleum and Energy Research, Bartlesville, Oklahoma 74005.

Applied and Environmental Microbiology
|January 1, 1986
PubMed

More Related Videos

Standardized Method for High-throughput Sterilization of Arabidopsis Seeds08:13

Standardized Method for High-throughput Sterilization of Arabidopsis Seeds

Published on: October 17, 2017

Adherence of Bacteria to Plant Surfaces Measured in the Laboratory07:07

Adherence of Bacteria to Plant Surfaces Measured in the Laboratory

Published on: June 19, 2018

Related Concept Videos

Methods of Sterilization I: Physical Methods01:29

Methods of Sterilization I: Physical Methods

As used in a healthcare facility, sterilization destroys all microorganisms through physical or chemical methods. The physical method includes steam, dry heat, boiling water, and radiation.
Steam sterilization uses non-toxic, low-cost moist heat in the form of saturated steam under pressure, which is fast, microbicidal, and sporicidal, and quickly warms and penetrates fabrics. Autoclaves, or steam sterilizers, expose each item to direct steam contact for a predetermined time at the necessary...
Physical Methods for Controlling Microbial Growth: Temperature01:23

Physical Methods for Controlling Microbial Growth: Temperature

Heat is a widely used method to control microbial growth by targeting and denaturing cellular proteins, thereby killing or inactivating microbes. This method's effectiveness is quantified using parameters such as the thermal death point (TDP), thermal death time (TDT), and decimal reduction time (D value). TDP represents the lowest temperature at which all microorganisms in a liquid suspension are eliminated within 10 minutes, whereas TDT is the time necessary to achieve sterilization at a...
Methods of Sterilization II: Chemical Methods01:30

Methods of Sterilization II: Chemical Methods

In healthcare, the chemical method of sterilization uses chemical sterilants to treat surgical instruments and medical supplies to help prevent the transmission of infectious pathogens to patients. Due to heat sensitivity, most medical supplies and equipment should not be exposed to high temperatures. These parts include rubber, plastic, glass, and other similar elements.
Using chemical sterilization rather than heat to clean out equipment is recommended. It eradicates and removes all bacteria,...
Physical Methods for Controlling Microbial Growth: Radiation and Filtration01:26

Physical Methods for Controlling Microbial Growth: Radiation and Filtration

Radiation and filtration are essential tools for microbial control, targeting microorganisms through distinct mechanisms. Radiation eliminates microbes by damaging their DNA, either killing them or inhibiting their growth. Based on wavelength, radiation is classified into two types: nonionizing and ionizing radiation.Non-ionizing radiation, such as UV radiation (200–400 nm), is absorbed by DNA, causing defects that effectively disinfect surfaces, air, and water, including safety cabinets.
Key Techniques in Microbiology01:19

Key Techniques in Microbiology

Aseptic techniques prevent contamination, ensure experimental accuracy, and protect researchers and microbial cultures. These techniques are essential in clinical, industrial, and research settings where sterility is required.Maintaining Sterility in Laboratory PracticesScientists maintain sterility by sterilizing tools with heat or chemicals, disinfecting work surfaces, and handling cultures in controlled environments. Working near an open flame or within a laminar flow hood reduces the risk...
Porosity and Absorption of Aggregate01:20

Porosity and Absorption of Aggregate

Aggregates contain pores of varying sizes; while some are completely enclosed within the particles, others open onto the surface, allowing water to penetrate. The porosity of aggregates is a major factor contributing to the overall porosity of concrete, given that aggregates constitute about three-quarters of concrete's volume.
When all pores in an aggregate are filled with water, the aggregate is considered saturated and surface-dry. If left in dry air, water will evaporate until the aggregate...