Related Experiment Video

Updated: Aug 3, 2026

Design and Construction of an Urban Runoff Research Facility
13:48

Design and Construction of an Urban Runoff Research Facility

Published on: August 8, 2014

Integration and application of the Rainfall Runoff Library

S Kim1, R A Vertessy, J-M Perraud

  • 1Dept. of Environ. Eng., Pusan National University, San 30, Jangjundong, Gumjunggu, Pusan, Republic of Korea, 609-735. kimsangh@pnu.edu

Water Science and Technology : a Journal of the International Association on Water Pollution Research
|February 1, 2006
PubMed

More Related Videos

A Protocol for Conducting Rainfall Simulation to Study Soil Runoff10:35

A Protocol for Conducting Rainfall Simulation to Study Soil Runoff

Published on: April 3, 2014

Vegetated Treatment Systems for Removing Contaminants Associated with Surface Water Toxicity in Agriculture and Urban Runoff08:49

Vegetated Treatment Systems for Removing Contaminants Associated with Surface Water Toxicity in Agriculture and Urban Runoff

Published on: May 15, 2017

Related Concept Videos

Precipitation Processes01:12

Precipitation Processes

The experimental conditions in a gravimetric analysis should be optimized to maximize the particle size and purity of the obtained precipitate. Ideally, the concentration of the precipitating reagent should be low with effective stirring to maintain low relative supersaturation for the growth of large crystals. In homogeneous precipitation, the precipitant is slowly generated by a chemical reaction in the solution to avoid local reagent excesses. For example, urea decomposes gradually to...
Conservation of Mass in Moving, Nondeforming Control Volume01:14

Conservation of Mass in Moving, Nondeforming Control Volume

Stormwater detention basins are essential in managing runoff during heavy rainfall, particularly in urban areas where impervious surfaces increase the risk of flooding. Understanding the conservation of mass in these systems allows engineers to optimize basin performance, balancing inflow, outflow, and water storage.
In the context of a detention basin, the conservation of mass states that the total mass of water entering the basin must equal the mass leaving the basin plus any accumulation of...
Design Example: Design of an Irrigation Channel01:27

Design Example: Design of an Irrigation Channel

Trapezoidal channels are widely used in irrigation systems due to their cost-effectiveness and efficiency in conveying water. Trapezoidal channels feature a flat bottom and sloping sides, making them stable and easier to construct compared to other shapes. The bottom width and side slope ratio are determined based on the required flow capacity and site conditions. The side slope is kept gentle for unlined channels to prevent soil erosion.Hydraulic parameters in channel design include the flow...
Design Example: Analyzing Capacity Contours for Flood Risk Assessment01:17

Design Example: Analyzing Capacity Contours for Flood Risk Assessment

Flood risk assessment involves careful planning and analysis to ensure the safety of communities near water retention structures. Capacity contours are a vital tool in this process, as they illustrate the potential spread of water at specific levels in a given area. In the context of building a bund across a small valley, these contours play a critical role in evaluating the safety of nearby residential areas.In this example, the bund is intended to store stormwater in the valley. The engineers...
Indefinite Integrals01:25

Indefinite Integrals

The water inflow rate into a storage tank is not constant but increases over time. Initially, the pump delivers water at a rate of 5 L/min. However, the inflow rate increases by 2 L/min for each additional minute due to rising pressure or system adjustments. This scenario can be described mathematically by a linear function:It is necessary to integrate the inflow rate function to measure the total volume of water added to the tank over time. The total water volume V(t) is obtained by performing...
Applications of Integration to Find Hydrostatic Pressure01:30

Applications of Integration to Find Hydrostatic Pressure

Hydrostatic force is a fluid's total force at rest on a surface. For a horizontal surface submerged at a fixed depth, the pressure is constant and calculated as the product of fluid density, gravitational acceleration, and depth. In the case of a vertical dam wall submerged in water, this force is not evenly distributed due to the increasing pressure with depth. This variation arises from the cumulative weight of the water above each point. Integration is used to account for the continuous...