Related Experiment Video

Updated: Aug 7, 2026

A Microfluidic Approach for the Study of Ice and Clathrate Hydrate Crystallization
08:01

A Microfluidic Approach for the Study of Ice and Clathrate Hydrate Crystallization

Published on: August 18, 2022

Texture change of ice on anomalously preserved methane clathrate hydrate

Wataru Shimada1, Satoshi Takeya, Yasushi Kamata

  • 1National Institute of Advanced Industrial Science and Technology (AIST), Tsukisamu-Higashi, Sapporo 062-8517, Japan.

The Journal of Physical Chemistry. B
|July 21, 2006
PubMed

More Related Videos

Methane Hydrate Crystallization on Sessile Water Droplets08:46

Methane Hydrate Crystallization on Sessile Water Droplets

Published on: May 26, 2021

Protocol for Measuring the Thermal Properties of a Supercooled Synthetic Sand-water-gas-methane Hydrate Sample09:46

Protocol for Measuring the Thermal Properties of a Supercooled Synthetic Sand-water-gas-methane Hydrate Sample

Published on: March 21, 2016

Related Concept Videos

Phase Transitions: Sublimation and Deposition02:33

Phase Transitions: Sublimation and Deposition

Some solids can transition directly into the gaseous state, bypassing the liquid state, via a process known as sublimation. At room temperature and standard pressure, a piece of dry ice (solid CO2) sublimes, appearing to gradually disappear without ever forming any liquid. Snow and ice sublimate at temperatures below the melting point of water, a slow process that may be accelerated by winds and the reduced atmospheric pressures at high altitudes. When solid iodine is warmed, the solid sublimes...
Phase Transitions: Melting and Freezing02:39

Phase Transitions: Melting and Freezing

Heating a crystalline solid increases the average energy of its atoms, molecules, or ions, and the solid gets hotter. At some point, the added energy becomes large enough to partially overcome the forces holding the molecules or ions of the solid in their fixed positions, and the solid begins the process of transitioning to the liquid state or melting. At this point, the temperature of the solid stops rising, despite the continual input of heat, and it remains constant until all of the solid is...
Inductive Effects on Chemical Shift: Overview01:27

Inductive Effects on Chemical Shift: Overview

The protons in unsubstituted alkanes are strongly shielded with chemical shifts below 1.8 ppm. Methine, methylene, and methyl protons appear at approximately 1.7, 1.2 and 0.7 ppm, while the proton signal from methane appears at 0.23 ppm. An electronegative substituent, such as chlorine, withdraws the electron density from the protons, increasing their chemical shift. Progressive substitution of the hydrogens in methane by chlorine shifts the proton signals increasingly downfield, to 3.05 ppm in...
States of Matter and Phase Changes00:59

States of Matter and Phase Changes

The internal energy of a substance—the total kinetic energy of all its molecules and the potential energy of their associated forces—depends on the strength of the intermolecular forces in the condensed phases and the pressure exerted on the substance. The internal energy of a substance is the highest in the gaseous state, the lowest in the solid state, and intermediate in the liquid state. Phase transitions are caused by changes in physical conditions, such as temperature and pressure, that...
Aldehydes and Ketones with Water: Hydrate Formation01:20

Aldehydes and Ketones with Water: Hydrate Formation

An oxygen-based nucleophile, like water, can undergo addition reactions with aldehydes and ketones. The reaction leads to the formation of hydrates, also referred to as 1,1-diols or geminal diols.
The formation of hydrates is a reversible reaction. Hydrate formation is influenced by steric and electronic factors accompanying the alkyl substituents on the carbonyl group: The rate of hydrate formation increases with a decrease in the number of alkyl groups attached to the carbonyl carbon. Hence,...
Unsoundness of Aggregate due to Volume Change01:26

Unsoundness of Aggregate due to Volume Change

Unsoundness in aggregates due to volume changes is primarily caused by the physical alterations aggregates undergo, such as freezing and thawing, thermal changes, and wetting and drying. Unsound aggregates, when subjected to these changes, result in volume change upon disintegration. This, in turn, contributes to the deterioration of concrete, including scaling, pop-outs, and cracking. Particular types of aggregates, such as porous flints, cherts, and those containing clay minerals, are...