Related Experiment Video

Updated: Jul 19, 2026

Temporomandibular Joint Pain Measurement by Bite Force and Von Frey Filament Assays in Mice
06:37

Temporomandibular Joint Pain Measurement by Bite Force and Von Frey Filament Assays in Mice

Published on: September 13, 2024

Mechanical work during stress-field translation in the human TMJ

L M Gallo1, G Chiaravalloti, L R Iwasaki

  • 1Clinic for Masticatory Disorders and Complete Dentures, Center for Oral Medicine, Dental and Maxillo-Facial Surgery, University of Zürich, Plattenstrasse 11, CH-8028 Zürich, Switzerland. luigi@zui.unizh.ch

Journal of Dental Research
|October 26, 2006
PubMed

More Related Videos

A Morphometric and Cellular Analysis Method for the Murine Mandibular Condyle08:07

A Morphometric and Cellular Analysis Method for the Murine Mandibular Condyle

Published on: January 11, 2018

In situ Compressive Loading and Correlative Noninvasive Imaging of the Bone-periodontal Ligament-tooth Fibrous Joint07:09

In situ Compressive Loading and Correlative Noninvasive Imaging of the Bone-periodontal Ligament-tooth Fibrous Joint

Published on: March 7, 2014

Related Concept Videos

True Stress and True Strain01:28

True Stress and True Strain

Engineering stress is calculated as the load divided by the original, undeformed cross-sectional area. It approximates a material under load. This approximation is especially relevant post-yield in ductile materials. Though engineering stress-strain diagrams are often used for their convenience and accessibility, they can sometimes fall short in accuracy, particularly when dealing with large strain values.
In contrast, true stress offers a more precise portrayal. It is computed by dividing the...
Bearing Stress01:22

Bearing Stress

Bearing stress refers to the contact pressure between two separate bodies. To visualize this, imagine a bolt thrust through a plate. The bolt applies a force to the plate, which exerts an equal but opposite force back onto the bolt. This force isn't just a singular entity but a compilation of numerous smaller forces distributed across the contact surface between the bolt and the plate.
Due to the intricacy of these microforces, an average value, known as bearing stress, is often used by...
Stress: General Loading Conditions01:15

Stress: General Loading Conditions

To grasp the intricacy of real-world conditions where multiple loads are applied simultaneously to a structure, one might visualize a section passing through a specific point within a body, aligned parallel to the xy plane. This section is subjected to various forces, including original loads, normal forces, and shearing forces.
The shearing force, possessing potential directionality within the plane of the section, is simplified into two component forces running parallel to the x and y axes.
Stress Concentrations in Circular Shafts01:18

Stress Concentrations in Circular Shafts

Consider the elastic torsion formula, which applies to a circular shaft with a consistent cross-section. This formula assumes that the shaft's ends are loaded with rigid plates firmly attached. However, in many cases, torques are applied to the shaft through mechanisms like flange couplings or gears, which are connected by keys inserted into keyways. This application method modifies the stress distribution near the point of torque application, causing it to deviate from the distributions...
Cell-matrix's Response to Mechanical Forces01:13

Cell-matrix's Response to Mechanical Forces

In animal cells, the extracellular matrix allows cells within tissues to withstand external stresses and transmits signals from the outside of the cell to the inside. The extracellular matrix is extensive, and its composition varies between different types of tissues. For example, the reticular fibers and ground substance make up the ECM in loose connective tissue, while collagen and bone minerals make up the ECM of bone tissue. 
Anchoring junctions mechanically attach a cell to the...
Transformation of Plane Stress01:18

Transformation of Plane Stress

Studying stress transformation is essential in understanding how stress components within a material, like a cube under plane stress, change with rotation. This change is analyzed by considering a prismatic element within the cube. As the element rotates, the stress components acting on it—both normal and shearing stresses—change in magnitude and orientation. This change is quantified using trigonometric functions of the rotation angle, relating the forces acting on the rotated element's faces...