Related Experiment Video

Updated: Jul 14, 2026

A Finite Element Approach for Locating the Center of Resistance of Maxillary Teeth
10:50

A Finite Element Approach for Locating the Center of Resistance of Maxillary Teeth

Published on: April 8, 2020

[Analysis on the stress induced by non metallic posts in dental and periodontal support by using the finite element

Anca Viţalariu1, R Comăneci, Monica Tatarciuc

  • 1Universitatea de Medicină şi Farmacie Gr.T. Popa Iaşi, Facultatea de Medicină Dentară.

Revista Medico-Chirurgicala a Societatii De Medici Si Naturalisti Din Iasi
|June 19, 2007
PubMed
Abstract

More Related Videos

A Coupled Experiment-finite Element Modeling Methodology for Assessing High Strain Rate Mechanical Response of Soft Biomaterials11:28

A Coupled Experiment-finite Element Modeling Methodology for Assessing High Strain Rate Mechanical Response of Soft Biomaterials

Published on: May 18, 2015

Finite Element Analysis Model for Assessing Expansion Patterns from Surgically Assisted Rapid Palatal Expansion07:16

Finite Element Analysis Model for Assessing Expansion Patterns from Surgically Assisted Rapid Palatal Expansion

Published on: October 20, 2023

Related Concept Videos

Stress: General Loading Conditions01:15

Stress: General Loading Conditions

To grasp the intricacy of real-world conditions where multiple loads are applied simultaneously to a structure, one might visualize a section passing through a specific point within a body, aligned parallel to the xy plane. This section is subjected to various forces, including original loads, normal forces, and shearing forces.
The shearing force, possessing potential directionality within the plane of the section, is simplified into two component forces running parallel to the x and y axes.
Stress Concentrations01:13

Stress Concentrations

The concept of stress concentration is crucial for understanding how materials respond under bending stresses, particularly when there are irregularities or discontinuities in the material's geometry. Normally, stress in a symmetric member subjected to pure bending is assumed to be uniformly distributed across the entire cross-section. However, this assumption does not hold when there are variations in the cross-sectional geometry or the presence of notches and holes.
The stress concentration...
Stress Concentrations01:24

Stress Concentrations

Stress concentration is when stress intensifies near discontinuities such as holes or abrupt cross-sectional changes in a structural member. This localized stress can often surpass the average stress within the member. The stress distribution in flat bars, either with a circular hole or varying widths connected by fillets, can be determined experimentally using a photoelastic method. The results are based on ratios of geometric parameters like the ratio of the hole's radius to the smaller width...
Applications of Stress01:04

Applications of Stress

Consider a structure made of a boom and a rod designed to support a load. These two components are connected by a pin and stabilized by brackets and pins. The boom and the rod are detached from their supports to assess the different stresses imposed on this structure, and a free-body diagram is drawn. Then, all the forces applied, including the load acting on the structure, are identified. The reaction forces exerted on both the boom and the rod are computed using the equilibrium equations.
The...
Flexural Stress01:16

Flexural Stress

When analyzing bending in symmetric members, it's crucial to understand how stresses distribute when subjected to bending moments. This stress distribution is effectively described by applying fundamental mechanics and material science principles, particularly Hooke's Law for elastic materials.
Hooke's Law states that within the material's elastic limits, stress is directly proportional to strain. In a member experiencing a bending moment, the strain at any point is relative to its distance...
Stresses under Combined Loadings01:23

Stresses under Combined Loadings

When analyzing a bent tube with a circular cross-section subjected to multiple forces, it is crucial to determine the stress distribution in order to maintain structural integrity under varied load conditions.
The process begins by slicing the tube at critical points and analyzing the internal forces and stress components at these sections, focusing on the centroid. Normal stresses, generated by axial forces and bending moments, are either compressive or tensile and vary across the section from...