Related Experiment Video

Updated: Jul 14, 2026

Measurement of Chladni Mode Shapes with an Optical Lever Method
04:39

Measurement of Chladni Mode Shapes with an Optical Lever Method

Published on: June 5, 2020

The modal low frequency noise of an elastically supported circular plate

Wojciech P Rdzanek1, Witold J Rdzanek, Zbigniew Engel

  • 1Department of Acoustics, University of Rzeszów, Rzeszów, Poland. wprdzank@univ.rzeszow.pl

International Journal of Occupational Safety and Ergonomics : JOSE
|June 30, 2007
PubMed

More Related Videos

Conducting Elevated Temperature Normal and Combined Pressure-Shear Plate Impact Experiments Via a Breech-end Sabot Heater System10:52

Conducting Elevated Temperature Normal and Combined Pressure-Shear Plate Impact Experiments Via a Breech-end Sabot Heater System

Published on: August 7, 2018

An Analog Macroscopic Technique for Studying Molecular Hydrodynamic Processes in Dense Gases and Liquids11:03

An Analog Macroscopic Technique for Studying Molecular Hydrodynamic Processes in Dense Gases and Liquids

Published on: December 4, 2017

Related Concept Videos

Fluid Pressure over Curved Plate of Constant Width01:12

Fluid Pressure over Curved Plate of Constant Width

When a curved plate of constant width is submerged in a liquid, the pressure acting normal to the plate varies continuously both in magnitude and direction. Calculating the magnitude and location of the resultant force at a point is often challenging for such cases. One of the methods to determine the resultant force and its location involves separately calculating the horizontal and vertical components of the resultant force. This complex calculation can be simplified by representing the...
Fluid Pressure over Flat Plate of Constant Width01:05

Fluid Pressure over Flat Plate of Constant Width

When a body is submerged in water, it experiences fluid pressure acting normal on its surface and distributed over its area. For better design structures, it is crucial to determine the magnitude and location of the resultant force acting on the surface. In the case of a rectangular plate of constant width submerged in water, the pressure increases with depth, resulting in a linearly varying trapezoidal pressure distribution from the upper to the lower edge of the plate.
The resultant force...
Magnetic Damping01:17

Magnetic Damping

Eddy currents can produce significant drag on motion, called magnetic damping. For instance, when a metallic pendulum bob swings between the poles of a strong magnet, significant drag acts on the bob as it enters and leaves the field, quickly damping the motion.
If, however, the bob is a slotted metal plate, the magnet produces a much smaller effect. When a slotted metal plate enters the field, an emf is induced by the change in flux; however, it is less effective because the slots limit the...
Fluid Pressure over Flat Plate of Variable Width01:02

Fluid Pressure over Flat Plate of Variable Width

When a flat plate is submerged in a fluid, the fluid exerts pressure on the plate. This pressure can lead to many different phenomena, including drag and buoyancy. To understand the behavior of the fluid over a flat plate of variable width, it is essential to analyze the distribution of the pressure exerted.
The pressure distribution on the plate can be calculated by determining the force that acts on a differential area strip of the plate. Thus, the magnitude of the force is equal to the...
Steady, Laminar Flow Between Parallel Plates01:17

Steady, Laminar Flow Between Parallel Plates

Understanding steady, laminar flow between parallel plates is essential for analyzing and designing flow in narrow rectangular channels, commonly found in various water conveyance and drainage systems. The Navier-Stokes equations govern fluid motion and are generally challenging to solve due to their nonlinearity. However, simplifications are possible in certain cases, like the steady laminar flow between parallel plates. For this scenario, we assume steady, incompressible, laminar flow.
Circular Shafts - Elastoplastic Materials01:24

Circular Shafts - Elastoplastic Materials

The study of solid circular shafts under stress shows that within the elastic limit, stress increases directly to the distance from the shaft's center. This relationship holds until the shaft reaches a critical point of stress, beyond which it begins to yield, marking the transition from elastic to plastic deformation. At this crucial juncture, the maximum torque the shaft can endure without permanent deformation is determined, signifying the limit of its elastic behavior.
As torque on the...