Related Experiment Video

Updated: Jul 13, 2026

Standardized Histomorphometric Evaluation of Osteoarthritis in a Surgical Mouse Model
07:32

Standardized Histomorphometric Evaluation of Osteoarthritis in a Surgical Mouse Model

Published on: May 6, 2020

Allometric relationships between knee cartilage volume, thickness, surface area and body dimensions

I G Otterness1, M-P H Le Graverand, F Eckstein

  • 1Division of Biomedical and Pharmaceutical Sciences, University of Rhode Island, Kingston, RI, USA. igo@otterness.net

Osteoarthritis and Cartilage
|July 10, 2007
PubMed
Abstract

More Related Videos

Establishment and Evaluation of a Sheep Model of Full-thickness Osteochondral Defect05:23

Establishment and Evaluation of a Sheep Model of Full-thickness Osteochondral Defect

Published on: April 14, 2026

Software-Assisted Quantitative Measurement of Osteoarthritic Subchondral Bone Thickness08:52

Software-Assisted Quantitative Measurement of Osteoarthritic Subchondral Bone Thickness

Published on: March 18, 2022

Related Concept Videos

Growth of Cartilage and Bone Tissue01:27

Growth of Cartilage and Bone Tissue

Chondrocytes form a temporary cartilaginous model by dividing and secreting a thick gel-like extracellular matrix. Once the chondrocytes undergo programmed cell death, osteoblasts enter the site of the cartilaginous model. The process of replacing the temporary cartilaginous model with bone in an ordered manner is called endochondral ossification. In endochondral ossification, not all of the cartilage is replaced by bone tissue. Some cartilage that performs a protective and supportive function...
Bones of the Lower Limb: Femur and Patella01:16

Bones of the Lower Limb: Femur and Patella

The femur is the body's longest and strongest bone spanning the thigh region. Its head articulates with the acetabulum of the hip bone to form the hip joint. A minor indentation on the medial side of the femoral head, called the fovea capitis, serves as the site of attachment for the ligament of the head of the femur. This weak ligament spans the femur and acetabulum and supports the hip joint. The narrowed region below the head is the neck of the femur. The inclination angle between the neck...
Changes in the Appendicular Skeleton with Age01:09

Changes in the Appendicular Skeleton with Age

The upper and lower limb initially develops as a small bulge called a limb bud, which appears on the lateral side of the early embryo. The upper limb bud appears near the end of the fourth week of development, with the lower limb bud appearing shortly after.
Initially, the limb buds consist of a core of mesenchyme covered by a layer of ectoderm. The ectoderm at the end of the limb bud thickens to form a narrow crest called the apical ectodermal ridge. This ridge stimulates the underlying...
Knee Joint01:23

Knee Joint

The knee joint is the most complicated joint in the body. It consists of three articulations– two tibiofemoral and one patellofemoral. As is characteristic of synovial joints, the knee joint has a thin articular capsule that partially surrounds this joint cavity. Additionally, several ligaments, muscles, and cartilaginous structures support the movement of the knee.
A total of seven ligaments support the knee joint. The patellar ligament, which is also attached to the quadriceps femoris group...
Development of the Limb Synovial Joints01:07

Development of the Limb Synovial Joints

Joints form during embryonic development in conjunction with the formation and growth of the associated bones. The embryonic tissue that gives rise to all bones, cartilage, and connective tissues of the body is called mesenchyme.
The mesenchymal stem cells differentiate into chondrocytes that form the hyaline cartilage, and later the cartilaginous model of the bone. This model further transforms into a bone. This process is known as endochondral ossification.
During development, the limbs...
Finding Volume Using Cross-Sectional Area01:25

Finding Volume Using Cross-Sectional Area

For solids whose cross-sectional areas vary in a predictable way, volume can be determined by integrating these areas along an axis perpendicular to the slices. This approach is particularly useful for polyhedral solids, where classical geometric formulas may not be immediately applicable. A tetrahedron provides a clear example of how cross-sectional integration can be applied to a three-dimensional object with continuously changing geometry.Consider a tetrahedron with height h and a base that...