Related Experiment Video

Updated: Jul 12, 2026

Experimental Procedure for Warm Spinning of Cast Aluminum Components
07:36

Experimental Procedure for Warm Spinning of Cast Aluminum Components

Published on: February 1, 2017

Precipitation hardening in the first aerospace aluminum alloy: the wright flyer crankcase

F W Gayle, M Goodway

    Science (New York, N.Y.)
    |November 11, 1994
    PubMed

    More Related Videos

    Conducting Elevated Temperature Normal and Combined Pressure-Shear Plate Impact Experiments Via a Breech-end Sabot Heater System10:52

    Conducting Elevated Temperature Normal and Combined Pressure-Shear Plate Impact Experiments Via a Breech-end Sabot Heater System

    Published on: August 7, 2018

    Casting Protocols for the Production of Open Cell Aluminum Foams by the Replication Technique and the Effect on Porosity09:22

    Casting Protocols for the Production of Open Cell Aluminum Foams by the Replication Technique and the Effect on Porosity

    Published on: December 11, 2014

    Related Concept Videos

    Thin-Walled Hollow Shafts01:15

    Thin-Walled Hollow Shafts

    In analyzing a thin-walled hollow shaft subjected to torsional loading, a segment with width dx is isolated for examination. Despite its equilibrium state, this segment faces torsional shearing forces at its ends. These forces are quantitatively described by the product of the longitudinal shearing stress on the segment's minor surface and the area of this surface, leading to the concept of shear flow. This shear flow is consistent throughout the structure, indicating a uniform distribution of...
    Accelerated Curing of Concrete01:25

    Accelerated Curing of Concrete

    Accelerating concrete curing is achieved by applying heat and additional moisture. This process accelerates the hydration of the cement, resulting in an earlier strength gain in the concrete. Steam curing is a method wherein the concrete products are either transported through a chamber on a conveyor belt or encased in plastic, allowing steam at atmospheric pressure to circulate freely around them. This process begins with a phase of moist curing that typically lasts between 3 to 5 hours, after...
    Toughness and Hardness of Aggregate01:22

    Toughness and Hardness of Aggregate

    Toughness and hardness are critical properties of aggregate materials used in concrete, particularly on pavement surfaces and industrial flooring subjected to heavy loads. Toughness is defined as the aggregate's resistance to failure by impact and is measured by the aggregate impact value (AIV). For this, the aggregate impact value test is performed, wherein the impact is delivered by a standard hammer, which falls freely under its own weight onto the aggregates. The aggregates fragment in the...
    Alkenes via Reductive Coupling of Aldehydes or Ketones: McMurry Reaction01:22

    Alkenes via Reductive Coupling of Aldehydes or Ketones: McMurry Reaction

    The radical dimerization of ketones or aldehydes gives vicinal diols through a pinacol coupling reaction. However, the behavior of titanium metals used for the reaction as a source of electrons is unusual. When the reaction is carried out in the presence of titanium, diols can be isolated at low temperatures. Else titanium further reacts with diols, forming alkenes through the McMurry reaction.
    Washing, Drying, and Ignition of Precipitates00:52

    Washing, Drying, and Ignition of Precipitates

    After filtration, the precipitate is washed to remove coprecipitated impurities and any remaining mother liquor. Colloidal precipitates, such as silver chloride, are washed with an electrolyte (such as dilute nitric acid) to prevent the peptization of the precipitate. In the case of slightly soluble precipitates, the wash solution contains a common ion to reduce solubility. Lead sulfate, which is slightly soluble in water, is washed with dilute sulfuric acid. Similarly, wash solutions may be...
    Design of Transmission Shafts01:16

    Design of Transmission Shafts

    The design of a transmission shaft is governed by two primary specifications: the power it transmits and its rotational speed. These parameters guide the selection of the shaft's material and cross-sectional dimensions, ensuring that the material's maximum shearing stress remains within the elastic limit while transmitting the desired power at the given speed. The system's power is intrinsically linked to the applied torque. The torque applied to the shaft can be calculated by reconfiguring the...