Related Experiment Video

Updated: Jul 11, 2026

Atomic Force Microscopy Cantilever-Based Nanoindentation: Mechanical Property Measurements at the Nanoscale in Air and Fluid
08:58

Atomic Force Microscopy Cantilever-Based Nanoindentation: Mechanical Property Measurements at the Nanoscale in Air and Fluid

Published on: December 2, 2022

Calibration of the normal spring constant of microcantilevers in a parallel fluid flow

Gennady V Lubarsky1, Georg Hähner

  • 1EaStCHEM School of Chemistry, University of St. Andrews, North Haugh, St. Andrews KY16 9ST, United Kingdom.

The Review of Scientific Instruments
|October 2, 2007
PubMed

More Related Videos

Use of Atomic Force Microscopy to Measure Mechanical Properties and Turgor Pressure of Plant Cells and Plant Tissues11:18

Use of Atomic Force Microscopy to Measure Mechanical Properties and Turgor Pressure of Plant Cells and Plant Tissues

Published on: July 15, 2019

Covalent Immobilization of Proteins for the Single Molecule Force Spectroscopy11:13

Covalent Immobilization of Proteins for the Single Molecule Force Spectroscopy

Published on: August 20, 2018

Related Concept Videos

Measurement of Fluid Pressure01:16

Measurement of Fluid Pressure

Fluid pressure is commonly measured using devices called manometers, which rely on liquid columns to indicate pressure differences. The height of a liquid column in a manometer reflects the pressure exerted by the fluid, providing a simple yet effective means of measurement. Different types of manometers serve specific purposes based on their configurations and the type of fluids involved.
A basic form of manometer is the piezometer, a vertical tube open at the top and filled with the same...
Application of the Linear Momentum Equation01:15

Application of the Linear Momentum Equation

The application of the linear momentum equation can be used to analyze the forces needed to hold a 180-degree pipe bend in place with flowing water. In this case, water flows through the bend with a constant cross-sectional area of 0.01 square meters and a flow velocity of 15 meters per second. The pressure at the entrance is 0.2 Megapascals and the pressure at the exit is 0.16 Megapascals.
The goal is to determine the force components in the x and y directions to hold the pipe in place. Since...
Euler's Formula to Columns: Problem Solving01:23

Euler's Formula to Columns: Problem Solving

Euler's formula is used in structural engineering to determine the buckling load of columns under various conditions. However, when dealing with systems that incorporate both rigid elements and elastic components, such as springs, the analysis requires a finer approach to determine the critical load. The problem described involves two rigid bars connected at a pivot point with a spring attached and a vertical load applied at one end.
The system comprises two vertical rigid bars, AB and BC, of...
Pressure Variation in a Fluid at Rest01:11

Pressure Variation in a Fluid at Rest

In a fluid at rest, the pressure at any point beneath the fluid surface depends solely on the depth, not on the container's shape or size. This principle, known as hydrostatic pressure, arises because, in stationary fluids, there is no acceleration, meaning the forces within the fluid balance out. Only vertical forces, caused by the weight of the fluid above, contribute to pressure changes with depth.
When measuring pressure at two different levels within the fluid, the difference in pressure...
Fluid Pressure over Curved Plate of Constant Width01:12

Fluid Pressure over Curved Plate of Constant Width

When a curved plate of constant width is submerged in a liquid, the pressure acting normal to the plate varies continuously both in magnitude and direction. Calculating the magnitude and location of the resultant force at a point is often challenging for such cases. One of the methods to determine the resultant force and its location involves separately calculating the horizontal and vertical components of the resultant force. This complex calculation can be simplified by representing the...
Typical Model Studies01:30

Typical Model Studies

Fluid mechanics model studies often utilize scaled-down systems to predict fluid behavior in full-scale environments, such as river flows, dam spillways, and structures interacting with open surfaces. Maintaining Froude number similarity in river models is crucial, as it replicates surface flow features like wave patterns and velocities.