Related Experiment Video

Updated: Jul 10, 2026

Simultaneous Label-Free Autofluorescence Multi-Harmonic Microscopy
09:19

Simultaneous Label-Free Autofluorescence Multi-Harmonic Microscopy

Published on: August 29, 2025

Self-referencing of the carrier-envelope slip in a 6-fs visible parametric amplifier

Andrius Baltuska, Takao Fuji, Takayoshi Kobayashi

    Optics Letters
    |November 21, 2007
    PubMed

    More Related Videos

    20 mJ, 1 ps Yb:YAG Thin-disk Regenerative Amplifier10:17

    20 mJ, 1 ps Yb:YAG Thin-disk Regenerative Amplifier

    Published on: July 12, 2017

    Carrier Lifetime Measurements in Semiconductors through the Microwave Photoconductivity Decay Method07:38

    Carrier Lifetime Measurements in Semiconductors through the Microwave Photoconductivity Decay Method

    Published on: April 18, 2019

    Related Concept Videos

    Biasing of FET01:22

    Biasing of FET

    Biasing a Junction Field Effect Transistor (JFET) is crucial for setting operational parameters and ensuring efficient functioning in electronic circuits. JFETs are characterized by using a single carrier type in N-channel or P-channel configurations, where the channel is surrounded by PN junctions. These junctions are central to the device's ability to control current flow.
    In an N-channel JFET, the structure consists of N-type material forming the channel on a P-type substrate, with the gate...
    Small-Signal Analysis of MOSFET Amplifiers01:23

    Small-Signal Analysis of MOSFET Amplifiers

    In small-signal analysis, a MOSFET transistor amplifier acts as a linear amplifier when operating in its saturation region. The gate-to-source voltage (VGS) of the MOSFET is the sum of the DC biasing voltage and the small time-varying input signal. This combination sets up the operating point and modulates the drain current (ID) that flows from the drain to the source. When a small AC signal is superimposed on the DC bias voltage at the gate, the instantaneous drain current comprises three...
    Cascaded Op Amps01:16

    Cascaded Op Amps

    Operational amplifiers (op-amps) are versatile electronic components that can be interconnected in a cascade - one after another in a linear sequence. This cascading is possible due to their infinite input resistance and zero output resistance, allowing them to maintain their input-output relationships even when connected in series.
    In a cascaded system, each op-amp is referred to as a stage. The output of one stage drives the input of the subsequent stage. As the input signal passes through...
    MOSFET Amplifiers01:17

    MOSFET Amplifiers

    The MOSFET, when operating in its active region, functions as a voltage-controlled current source. In this region, the gate-to-source voltage controls the drain current. This principle underlies the operation of the transconductance MOSFET amplifier. The output current is directed through a load resistor to convert this amplifier into a voltage amplifier. The output voltage is then obtained by subtracting the voltage drop across the load resistance from the supply voltage. This process results...
    Small-Signal Analysis of BJT Amplifiers01:21

    Small-Signal Analysis of BJT Amplifiers

    Small signal analysis is a fundamental approach used in electronics to understand how a Bipolar Junction Transistor (BJT) amplifier processes signals. In the active region, the BJT is designed for linear amplification. The transistor's behavior under these conditions is governed by its instantaneous base-emitter voltage VBE, a sum of the DC bias VBE, and a small AC signal VBE, resulting in the collector current iC. Here, the collector current has a DC component and an AC component.
    Carrier Generation and Recombination01:22

    Carrier Generation and Recombination

    Carrier generation is the process by which electron-hole pairs (EHPs) are created within the semiconductor. In direct-bandgap semiconductors, such as gallium arsenide (GaAs), this occurs efficiently when energy absorption prompts valence electrons to leap into the conduction band, leaving behind holes.
    This process is given by the generation rate G and is efficient due to the conservation of momentum between the valence band maximum and conduction band minimum.
    Indirect generation involves an...