Related Experiment Video

Updated: Jul 9, 2026

Automation of Mode Locking in a Nonlinear Polarization Rotation Fiber Laser through Output Polarization Measurements
14:18

Automation of Mode Locking in a Nonlinear Polarization Rotation Fiber Laser through Output Polarization Measurements

Published on: February 28, 2016

Comparison of soliton robustness with respect to polarization-mode dispersion with first-order polarization-mode

C Xie, M Karlsson, H Sunnerud

    Optics Letters
    |November 28, 2007
    PubMed

    More Related Videos

    A Photonic System for Generating Unconditional Polarization-Entangled Photons Based on Multiple Quantum Interference07:56

    A Photonic System for Generating Unconditional Polarization-Entangled Photons Based on Multiple Quantum Interference

    Published on: September 5, 2019

    Rapid Repetition Rate Fluctuation Measurement of Soliton Crystals in a Microresonator07:42

    Rapid Repetition Rate Fluctuation Measurement of Soliton Crystals in a Microresonator

    Published on: December 15, 2021

    Related Concept Videos

    Pole and System Stability01:24

    Pole and System Stability

    The transfer function is a fundamental concept representing the ratio of two polynomials. The numerator and denominator encapsulate the system's dynamics. The zeros and poles of this transfer function are critical in determining the system's behavior and stability.
    Simple poles are unique roots of the denominator polynomial. Each simple pole corresponds to a distinct solution to the system's characteristic equation, typically resulting in exponential decay terms in the system's response.
    Second Order systems II01:18

    Second Order systems II

    In an underdamped second-order system, where the damping ratio ζ is between 0 and 1, a unit-step input results in a transfer function that, when transformed using the inverse Laplace method, reveals the output response. The output exhibits a damped sinusoidal oscillation, and the difference between the input and output is termed the error signal. This error signal also demonstrates damped oscillatory behavior. Eventually, as the system reaches a steady state, the error diminishes to zero.
    If  ζ...
    Second Order systems I01:20

    Second Order systems I

    A servo system exemplifies a second-order system, featuring a proportional controller and load elements that ensure the output position aligns with the input position. The relationship between these components is described by a second-order differential equation. Applying the Laplace transform under zero initial conditions yields the transfer function, showing how inputs are converted to outputs in the system.
    By reinterpreting the system, one can derive the closed-loop transfer function, which...
    ¹H NMR: Interpreting Distorted and Overlapping Signals01:02

    ¹H NMR: Interpreting Distorted and Overlapping Signals

    Spin systems where the difference in chemical shifts of the coupled nuclei is greater than ten times J are called first-order spin systems. These nuclei are weakly coupled, and their chemical shifts and coupling constant can generally be estimated from the well-separated signals in the spectrum.
    As Δν decreases and the signals move closer, the doublets appear increasingly distorted. The intensities of the inner lines increase at the cost of those of the outer lines as the signals are slanted or...
    Linear Approximation in Time Domain01:21

    Linear Approximation in Time Domain

    Nonlinear systems often require sophisticated approaches for accurate modeling and analysis, with state-space representation being particularly effective. This method is especially useful for systems where variables and parameters vary with time or operating conditions, such as in a simple pendulum or a translational mechanical system with nonlinear springs.
    For a simple pendulum with a mass evenly distributed along its length and the center of mass located at half the pendulum's length, the...
    Classification of Systems-I01:26

    Classification of Systems-I

    Linearity is a system property characterized by a direct input-output relationship, combining homogeneity and additivity.
    Homogeneity dictates that if an input x(t) is multiplied by a constant c, the output y(t) is multiplied by the same constant. Mathematically, this is expressed as: