Related Experiment Video

Updated: Jul 9, 2026

Transmission of Multiple Signals through an Optical Fiber Using Wavefront Shaping
09:43

Transmission of Multiple Signals through an Optical Fiber Using Wavefront Shaping

Published on: March 20, 2017

Signal and noise transfer in spatiotemporal quantum-based imaging systems

Reza Akbarpour1, Saul N Friedman, Jeffrey H Siewerdsen

  • 1Robarts Research Institute, Department of Medical Biophysics, University of Western Ontario, 100 Perth Drive,London, Ontario, Canada.

Journal of the Optical Society of America. A, Optics, Image Science, and Vision
|December 7, 2007
PubMed

More Related Videos

Quantum State Engineering of Light with Continuous-wave Optical Parametric Oscillators09:23

Quantum State Engineering of Light with Continuous-wave Optical Parametric Oscillators

Published on: May 30, 2014

Measurement of Quantum Interference in a Silicon Ring Resonator Photon Source12:19

Measurement of Quantum Interference in a Silicon Ring Resonator Photon Source

Published on: April 4, 2017

Related Concept Videos

¹H NMR: Interpreting Distorted and Overlapping Signals01:02

¹H NMR: Interpreting Distorted and Overlapping Signals

Spin systems where the difference in chemical shifts of the coupled nuclei is greater than ten times J are called first-order spin systems. These nuclei are weakly coupled, and their chemical shifts and coupling constant can generally be estimated from the well-separated signals in the spectrum.
As Δν decreases and the signals move closer, the doublets appear increasingly distorted. The intensities of the inner lines increase at the cost of those of the outer lines as the signals are slanted or...
Reconstruction of Signal using Interpolation01:10

Reconstruction of Signal using Interpolation

Signal processing techniques are essential for accurately converting continuous signals to digital formats and vice versa. When a continuous signal is sampled with a period T, the resulting sampled signal exhibits replicas of the original spectrum in the frequency domain, spaced at intervals equal to the sampling frequency. To handle this sampled signal, a zero-order hold method can be applied, which creates a piecewise constant signal by retaining each sample's value until the next sampling...
Signal and System01:26

Signal and System

A signal x(t) is a set of data or a time function representing a variable of interest. Signals typically convey information about a phenomenon, such as atmospheric temperature, humidity, human voice, television images, a dog's bark, or birdsongs. More generally, a signal can be a function of more than one independent variable. For instance, images depend on horizontal and vertical positions and can be regarded as two-dimensional signals. However, this text will focus on one-dimensional signals...
Aliasing01:18

Aliasing

Accurate signal sampling and reconstruction are crucial in various signal-processing applications. A time-domain signal's spectrum can be revealed using its Fourier transform. When this signal is sampled at a specific frequency, it results in multiple scaled replicas of the original spectrum in the frequency domain. The spacing of these replicas is determined by the sampling frequency.
If the sampling frequency is below the Nyquist rate, these replicas overlap, preventing the original signal...
NMR Spectrometers: Resolution and Error Correction01:14

NMR Spectrometers: Resolution and Error Correction

When magnetic nuclei in a sample achieve resonance and undergo relaxation, the signal detected in NMR is an approximately exponential free induction decay. Fourier transform of an exponential decay yields a Lorentzian peak in the frequency domain. Lorentzian peaks in an NMR spectrum are defined by their amplitude, full width at half maximum, and position, where the peak width is governed by the spin-spin relaxation time alone. In real experiments, however, the applied magnetic field is rendered...
Sampling Theorem01:15

Sampling Theorem

In signal processing, the analysis of continuous-time signals, denoted as x(t), often involves sampling techniques to convert these signals into discrete-time signals. This process is essential for digital representation and manipulation. A critical component in sampling is the train of impulses, characterized by the sampling interval and the sampling frequency. The relationship between these parameters and the original signal's properties dictates the success of the sampling process.