Related Experiment Video

Updated: Jul 8, 2026

Photoelectron Imaging of Anions Illustrated by 310 Nm Detachment of F−
06:53

Photoelectron Imaging of Anions Illustrated by 310 Nm Detachment of F−

Published on: July 27, 2018

Nonadiabatic interactions in the Cl + H2 reaction probed by ClH2- and ClD2- photoelectron imaging

Etienne Garand1, Jia Zhou, David E Manolopoulos

  • 1Department of Chemistry, University of California, Berkeley, CA 94720, USA.

Science (New York, N.Y.)
|January 5, 2008
PubMed

More Related Videos

Coulomb Explosion Imaging as a Tool to Distinguish Between Stereoisomers08:51

Coulomb Explosion Imaging as a Tool to Distinguish Between Stereoisomers

Published on: August 18, 2017

Measurement of Ultrafast Vibrational Coherences in Polyatomic Radical Cations with Strong-Field Adiabatic Ionization08:22

Measurement of Ultrafast Vibrational Coherences in Polyatomic Radical Cations with Strong-Field Adiabatic Ionization

Published on: August 6, 2018

Related Concept Videos

Photochemical Electrocyclic Reactions: Stereochemistry01:26

Photochemical Electrocyclic Reactions: Stereochemistry

The absorption of UV–visible light by conjugated systems causes the promotion of an electron from the ground state to the excited state. Consequently, photochemical electrocyclic reactions proceed via the excited-state HOMO rather than the ground-state HOMO. Since the ground- and excited-state HOMOs have different symmetries, the stereochemical outcome of electrocyclic reactions depends on the mode of activation; i.e., thermal or photochemical.
Selection Rules: Photochemical Activation
Cycloaddition Reactions: MO Requirements for Photochemical Activation01:12

Cycloaddition Reactions: MO Requirements for Photochemical Activation

Some cycloaddition reactions are activated by heat, while others are initiated by light. For example, a [2 + 2] cycloaddition between two ethylene molecules occurs only in the presence of light. It is photochemically allowed but thermally forbidden.
Electrophilic Addition of HX to 1,3-Butadiene: Thermodynamic vs Kinetic Control01:23

Electrophilic Addition of HX to 1,3-Butadiene: Thermodynamic vs Kinetic Control

The addition of a hydrogen halide to 1,3-butadiene gives a mixture of 1,2- and 1,4-adducts. Since more substituted alkenes are more stable, the 1,4-adduct is expected to be the major product. However, the product distribution is strongly influenced by temperature; low temperature favors the 1,2-adduct, whereas the 1,4-adduct is predominant at high temperature.
Electrophilic 1,2- and 1,4-Addition of HX to 1,3-Butadiene01:17

Electrophilic 1,2- and 1,4-Addition of HX to 1,3-Butadiene

The electrophilic addition of hydrogen halides such as HBr to alkenes and nonconjugated dienes gives a single product as per Markovnikov’s rule.
[4+2] Cycloaddition of Conjugated Dienes: Diels–Alder Reaction01:16

[4+2] Cycloaddition of Conjugated Dienes: Diels–Alder Reaction

The Diels–Alder reaction is an example of a thermal pericyclic reaction between a conjugated diene and an alkene or alkyne, commonly referred to as a dienophile. The reaction involves a concerted movement of six π electrons, four from the diene and two from the dienophile, forming an unsaturated six-membered ring. As a result, these reactions are classified as [4+2] cycloadditions.
Hess's Law03:40

Hess's Law

There are two ways to determine the amount of heat involved in a chemical change: measure it experimentally, or calculate it from other experimentally determined enthalpy changes. Some reactions are difficult, if not impossible, to investigate and make accurate measurements for experimentally. And even when a reaction is not hard to perform or measure, it is convenient to be able to determine the heat involved in a reaction without having to perform an experiment.