Calculating ground water transit time of horizontal flow through leaky aquifers

Related Experiment Video

Updated: Jul 8, 2026

Tracking Infiltration Front Depth Using Time-lapse Multi-offset Gathers Collected with Array Antenna Ground Penetrating Radar
07:14

Tracking Infiltration Front Depth Using Time-lapse Multi-offset Gathers Collected with Array Antenna Ground Penetrating Radar

Published on: May 1, 2018

Angelika C Braunsfurth1, Wilfried Schneider

  • 1Hamburg University of Technology, Institute of Water Resources and Water Supply, Schwarzenbergstrasse 95, 21073 Hamburg, Germany. hailer@tu-harburg.de

Ground Water
|January 10, 2008
PubMed

Keywords:
groundwater flow modelingaquifer leakage analysistransit time calculationhydrological modeling

More Related Videos

Measuring Carbon-based Contaminant Mineralization Using Combined CO2 Flux and Radiocarbon Analyses11:19

Measuring Carbon-based Contaminant Mineralization Using Combined CO2 Flux and Radiocarbon Analyses

Published on: October 21, 2016

Visualizing Hyporheic Flow Through Bedforms Using Dye Experiments and Simulation09:49

Visualizing Hyporheic Flow Through Bedforms Using Dye Experiments and Simulation

Published on: November 18, 2015

Related Concept Videos

Fundamental Theorem of Calculus I: Problem Solving01:22

Fundamental Theorem of Calculus I: Problem Solving

In many engineering and environmental applications, accumulated quantities are determined from rates that vary over time. A common example arises in water management, where a supply system pumps water into a storage tank at a rate that changes with time. Accurately determining how much water has entered the tank over a given period is essential for maintaining proper pressure, scheduling operations, and ensuring system safety.The flow rate of water into the tank is described by a time-dependent...
Uniform Depth Channel Flow: Problem Solving01:18

Uniform Depth Channel Flow: Problem Solving

To calculate the flow rate for a trapezoidal channel, first, identify the bottom width, side slope, and flow depth of the channel. The cross-sectional area (A) corresponding to the depth of flow (y), channel bottom width (B), and side slope (θ) is determined by:Next, calculate the wetted perimeter, which includes the bottom width and the sloped side lengths in contact with the water. Using the values of the cross-sectional area and the wetted perimeter, determine the hydraulic radius by...
Indefinite Integrals01:25

Indefinite Integrals

The water inflow rate into a storage tank is not constant but increases over time. Initially, the pump delivers water at a rate of 5 L/min. However, the inflow rate increases by 2 L/min for each additional minute due to rising pressure or system adjustments. This scenario can be described mathematically by a linear function:It is necessary to integrate the inflow rate function to measure the total volume of water added to the tank over time. The total water volume V(t) is obtained by performing...
Design Example: Design of an Irrigation Channel01:27

Design Example: Design of an Irrigation Channel

Trapezoidal channels are widely used in irrigation systems due to their cost-effectiveness and efficiency in conveying water. Trapezoidal channels feature a flat bottom and sloping sides, making them stable and easier to construct compared to other shapes. The bottom width and side slope ratio are determined based on the required flow capacity and site conditions. The side slope is kept gentle for unlined channels to prevent soil erosion.Hydraulic parameters in channel design include the flow...
Plane Potential Flows01:23

Plane Potential Flows

Plane potential flows simplify fluid motion by assuming the fluid to be irrotational and incompressible. These characteristics allow these flows to be described by a velocity potential function, ϕ, representing the flow speed in a given direction, and a stream function, ψ, that visualizes the flow path, both governed by Laplace's equation. These parameters help in estimating flow patterns, velocity distributions, and pressure fields around various hydraulic structures.
Uniform Flow
Uniform flow...
Hydraulic Jump: Problem Solving01:16

Hydraulic Jump: Problem Solving

To analyze a hydraulic jump in a rectangular channel with a flow speed of 6 meters per second, follow these steps:Calculate Effective Upstream Velocity:When the downstream gate closes, a hydraulic jump forms, traveling upstream at 2 meters per second. This wave speed combines with the initial channel flow velocity, creating an effective upstream velocity.Identify Flow Velocities Before and After the Hydraulic Jump:Upstream of the hydraulic jump, the effective flow velocity includes both the...