Related Experiment Video

Updated: Jul 8, 2026

Automation of Mode Locking in a Nonlinear Polarization Rotation Fiber Laser through Output Polarization Measurements
14:18

Automation of Mode Locking in a Nonlinear Polarization Rotation Fiber Laser through Output Polarization Measurements

Published on: February 28, 2016

Reduction of fiber-nonlinearity-enhanced amplifier noise by means of phase-sensitive amplifiers

W Imajuku, A Takada

    Optics Letters
    |January 1, 1997
    PubMed

    More Related Videos

    Shaping the Amplitude and Phase of Laser Beams by Using a Phase-only Spatial Light Modulator08:39

    Shaping the Amplitude and Phase of Laser Beams by Using a Phase-only Spatial Light Modulator

    Published on: January 28, 2019

    Related Concept Videos

    Time and frequency -Domain Interpretation of Phase-lag Control01:21

    Time and frequency -Domain Interpretation of Phase-lag Control

    Phase-lag controllers are widely used in control systems to improve stability and reduce steady-state errors. A dimmer switch controlling the brightness of a light bulb serves as a practical example of phase-lag control, gradually adjusting the bulb's brightness. Mathematically, phase-lag control or low-pass filtering is represented when the factor 'a' is less than 1.
    Phase-lag controllers do not place a pole at zero, but instead influence the steady-state error by amplifying any finite,...
    Small-Signal Analysis of MOSFET Amplifiers01:23

    Small-Signal Analysis of MOSFET Amplifiers

    In small-signal analysis, a MOSFET transistor amplifier acts as a linear amplifier when operating in its saturation region. The gate-to-source voltage (VGS) of the MOSFET is the sum of the DC biasing voltage and the small time-varying input signal. This combination sets up the operating point and modulates the drain current (ID) that flows from the drain to the source. When a small AC signal is superimposed on the DC bias voltage at the gate, the instantaneous drain current comprises three...
    Cascaded Op Amps01:16

    Cascaded Op Amps

    Operational amplifiers (op-amps) are versatile electronic components that can be interconnected in a cascade - one after another in a linear sequence. This cascading is possible due to their infinite input resistance and zero output resistance, allowing them to maintain their input-output relationships even when connected in series.
    In a cascaded system, each op-amp is referred to as a stage. The output of one stage drives the input of the subsequent stage. As the input signal passes through...
    Phase-lead and Phase-lag Controllers01:22

    Phase-lead and Phase-lag Controllers

    Understanding the working function of different types of controllers can be illustrated with practical analogies, such as adjusting a stereo's volume equalizer. Cranking up the bass involves a phase-lead controller, which functions as a high-pass filter, while increasing the treble uses a phase-lag controller, which acts as a low-pass filter. PD controllers, similar to high-pass filters, enhance the system's response to high-frequency components. PI controllers, akin to low-pass filters, manage...
    Time and frequency -Domain Interpretation of Phase-lead Control01:24

    Time and frequency -Domain Interpretation of Phase-lead Control

    Phase-lead controllers are commonly used in various control systems to enhance response speed and stability. Adjusting the brightness on a television screen offers a practical example of phase-lead control. When contrast is enhanced, a phase-lead controller is employed. Mathematically, phase-lead control is identified when the first parameter is smaller than the second.
    The design of phase-lead control involves the strategic placement of poles and zeros to balance steady-state error and system...
    Parallel Resonance01:23

    Parallel Resonance

    The parallel RLC circuit is an arrangement where the resistor (R), inductor (L), and capacitor (C) are all connected to the same nodes and, as a result, share the same voltage across them. The parallel RLC circuit is analyzed in terms of admittance (Y), which reflects the ease with which current can flow. The admittance is given by: