Transmission of encoded information based on antiphase dynamics

Related Experiment Video

Updated: Jul 8, 2026

Transmission of Multiple Signals through an Optical Fiber Using Wavefront Shaping
09:43

Transmission of Multiple Signals through an Optical Fiber Using Wavefront Shaping

Published on: March 20, 2017

E A Viktorov, P Mandel

    Optics Letters
    |January 12, 2008
    PubMed

    More Related Videos

    Shaping the Amplitude and Phase of Laser Beams by Using a Phase-only Spatial Light Modulator08:39

    Shaping the Amplitude and Phase of Laser Beams by Using a Phase-only Spatial Light Modulator

    Published on: January 28, 2019

    Real-Time Proxy-Control of Re-Parameterized Peripheral Signals using a Close-Loop Interface11:54

    Real-Time Proxy-Control of Re-Parameterized Peripheral Signals using a Close-Loop Interface

    Published on: May 8, 2021

    Related Concept Videos

    Time and frequency -Domain Interpretation of Phase-lag Control01:21

    Time and frequency -Domain Interpretation of Phase-lag Control

    Phase-lag controllers are widely used in control systems to improve stability and reduce steady-state errors. A dimmer switch controlling the brightness of a light bulb serves as a practical example of phase-lag control, gradually adjusting the bulb's brightness. Mathematically, phase-lag control or low-pass filtering is represented when the factor 'a' is less than 1.
    Phase-lag controllers do not place a pole at zero, but instead influence the steady-state error by amplifying any finite,...
    Time and frequency -Domain Interpretation of Phase-lead Control01:24

    Time and frequency -Domain Interpretation of Phase-lead Control

    Phase-lead controllers are commonly used in various control systems to enhance response speed and stability. Adjusting the brightness on a television screen offers a practical example of phase-lead control. When contrast is enhanced, a phase-lead controller is employed. Mathematically, phase-lead control is identified when the first parameter is smaller than the second.
    The design of phase-lead control involves the strategic placement of poles and zeros to balance steady-state error and system...
    Action Potential: Phases of Stimulation01:28

    Action Potential: Phases of Stimulation

    The action potential is a complex electrical event that occurs in excitable cells, such as neurons and muscle cells. It consists of several distinct phases, each with specific characteristics.
    Resting Phase:
    In this phase, the cell's membrane is at its resting potential, typically around -70 millivolts (mV) for neurons. Inside the cell, there is a higher concentration of potassium ions (K+) and a lower concentration of sodium ions (Na+). Voltage-gated sodium channels are closed, and...
    Properties of DTFT I01:24

    Properties of DTFT I

    In signal processing, Discrete-Time Fourier Transforms (DTFTs) play a critical role in analyzing discrete-time signals in the frequency domain. Various properties of the DTFTs such as linearity, time-shifting, frequency-shifting, time reversal, conjugation, and time scaling help understand and manipulate these signals for different applications.
    The linearity property of DTFTs is fundamental. If two discrete-time signals are multiplied by constants a and b respectively, and then combined to...
    Time-Domain Interpretation of PD Control01:07

    Time-Domain Interpretation of PD Control

    Proportional-Derivative (PD) control is a widely used control method in various engineering systems to enhance stability and performance. In a system with only proportional control, common issues include high maximum overshoot and oscillation, observed in both the error signal and its rate of change. This behavior can be divided into three distinct phases: initial overshoot, subsequent undershoot, and gradual stabilization.
    Consider the example of control of motor torque. Initially, a positive...
    Basic Discrete Time Signals01:16

    Basic Discrete Time Signals

    The unit step sequence is defined as 1 for zero and positive values of the integer n. This sequence can be graphically displayed using a set of eight sample points, showing a step function starting from n=0 and remaining constant thereafter.
    The unit impulse or sample sequence is mathematically expressed as zero for all n values except at n=0, where it is one. The unit impulse sequence, denoted by δ(n), is the first difference of the unit step sequence, while the unit step sequence u(n) is the...