Comparison of blood viscosity using a torsional oscillation viscometer and a rheometer

Related Experiment Video

Updated: Jul 8, 2026

Calibration Procedures for Orthogonal Superposition Rheology
08:43

Calibration Procedures for Orthogonal Superposition Rheology

Published on: November 18, 2020

Valter Travagli1, Iacopo Zanardi, Letizia Boschi

  • 1Dipartimento Farmaco Chimico Tecnologico, Università degli Studi di Siena, Italy. travagli@unisi.it

Clinical Hemorheology and Microcirculation
|January 17, 2008
PubMed

The absence of a simple and clinically practical method to determine whole blood viscosity can partly justify why the medical community has been slow in realizing the significance of whole blood viscosity. For this reason, the availability of a technique able to evaluate blood viscosity in a rapid and direct manner is welcome. To evaluate the feasibility in hemorheological laboratory of a new torsional oscillation viscometer, it was compared with a conventional cone-plate system. The viscosity comparison has been related to hematocrit value both on whole blood and suspended blood in a saline solution. The results showed a good repeatability and reproducibility of the new equipment, with a best-fitting data of the hematocrit 0-100% range characterized by coefficient of determinations, r2>0.95. Furthermore, a comparison of whole blood viscosity as measured by the two instruments was done on blood samples collected from hospitalized patients. Reasonable agreement for the viscosity values was found between the two methods with linear determination coefficients between the two measurement methods comprised between r2=0.7329 and 0.9263, depending on shear stress phase and the corresponding shear rate.

More Related Videos

Measurement of the Rheology of Crude Oil in Equilibrium with CO2 at Reservoir Conditions10:38

Measurement of the Rheology of Crude Oil in Equilibrium with CO2 at Reservoir Conditions

Published on: June 6, 2017

Rapid Viscoelastic Characterization of Airway Mucus Using a Benchtop Rheometer08:47

Rapid Viscoelastic Characterization of Airway Mucus Using a Benchtop Rheometer

Published on: April 21, 2022

Related Concept Videos

Viscosity of Fluid01:19

Viscosity of Fluid

Viscosity measures the resistance a fluid offers to flow and deformation. It results from internal friction between layers of fluid moving relative to one another. Dynamic viscosity, denoted by the Greek letter mu (μ), quantifies the force needed to move one fluid layer over another. For Newtonian fluids like water and air, the relationship between the shearing stress and the rate of shearing strain is linear, meaning their viscosity remains constant regardless of the applied stress.
Viscosity01:17

Viscosity

When water is poured into a glass, it falls freely and quickly, whereas if honey or maple syrup is poured over a pancake, it flows slowly and sticks to the surface of the container. This difference in the flow of different kinds of liquids arises due to the fluid friction between the liquid layers and the liquid and the surrounding material. This property of fluids is called fluid viscosity. In this example, water has a lower viscosity than honey and maple syrup.
The SI unit of viscosity is...
Viscosity01:27

Viscosity

Viscosity is a property of fluids that measures their resistance to flow. It is influenced by factors such as the surface area of contact, the gradient of flow speed, and the fluid's viscosity constant, called the coefficient of viscosity. The coefficient of viscosity, also known as dynamic viscosity, is denoted by the symbol η. It determines the proportionality between the viscous force and the gradient of flow speed.Newton's law of viscosity states that the viscous force on a faster-moving...
Thin-Walled Hollow Shafts01:15

Thin-Walled Hollow Shafts

In analyzing a thin-walled hollow shaft subjected to torsional loading, a segment with width dx is isolated for examination. Despite its equilibrium state, this segment faces torsional shearing forces at its ends. These forces are quantitatively described by the product of the longitudinal shearing stress on the segment's minor surface and the area of this surface, leading to the concept of shear flow. This shear flow is consistent throughout the structure, indicating a uniform distribution of...
Surface Tension, Capillary Action, and Viscosity02:57

Surface Tension, Capillary Action, and Viscosity

Surface Tension
The various IMFs between identical molecules of a substance are examples of cohesive forces. The molecules within a liquid are surrounded by other molecules and are attracted equally in all directions by the cohesive forces within the liquid. However, the molecules on the surface of a liquid are attracted only by about one-half as many molecules. Because of the unbalanced molecular attractions on the surface molecules, liquids contract to form a shape that minimizes the number...
Newtonian Fluid: Problem Solving01:18

Newtonian Fluid: Problem Solving

Newtonian fluids exhibit a constant viscosity, meaning their shear stress and shear strain rate are directly proportional. This property ensures a predictable and stable response to applied forces, maintaining a linear relationship between force and flow. Examples include water, air, and light oils, consistently demonstrating this proportional behavior regardless of external conditions.
A velocity gradient forms within the fluid when a Newtonian fluid is placed between two parallel plates, with...