Related Experiment Video

Updated: Jul 7, 2026

Automation of Mode Locking in a Nonlinear Polarization Rotation Fiber Laser through Output Polarization Measurements
14:18

Automation of Mode Locking in a Nonlinear Polarization Rotation Fiber Laser through Output Polarization Measurements

Published on: February 28, 2016

Berry's Phase Analysis of Polarization Rotation in Helicoidal Fibers

F Wassmann, A Ankiewicz

    Applied Optics
    |February 15, 2008
    PubMed

    More Related Videos

    Disentangling High Strength Copolymer Aramid Fibers to Enable the Determination of Their Mechanical Properties06:02

    Disentangling High Strength Copolymer Aramid Fibers to Enable the Determination of Their Mechanical Properties

    Published on: September 1, 2018

    Polarization-Sensitive Two-Photon Microscopy for a Label-Free Amyloid Structural Characterization05:54

    Polarization-Sensitive Two-Photon Microscopy for a Label-Free Amyloid Structural Characterization

    Published on: September 8, 2023

    Related Concept Videos

    Polar Coordinates: Problem Solving01:27

    Polar Coordinates: Problem Solving

    Directional radiation patterns are central to antenna analysis, as they illustrate how signal strength varies with direction. These patterns are often modeled using polar plots, where the radial distance from the origin represents signal intensity at a given angle. A commonly used idealized form is the four-lobed rose curve, which captures the concept of directional beams in a simplified mathematical form.The four-lobed rose curve, described by r = cos⁡(2θ), features four symmetric lobes, each...
    Angle of Twist: Problem Solving01:13

    Angle of Twist: Problem Solving

    An electric motor applies a torque of 700 N·m to an aluminum shaft, triggering a stable rotation. Two pulleys, B and C, are subjected to torques of 300 N·m and 400 N·m, respectively. The modulus of rigidity is provided as 25 GPa. With the knowledge of the length and diameter of each segment, the twist angle between the two pulleys can be computed. First, a section cut is made between pulleys B and C, and the cut cross-section is analyzed using a free-body diagram. Given that the torque exerted...
    Circular Shaft - Stresses in Linear Range01:13

    Circular Shaft - Stresses in Linear Range

    Consider a scenario where a circular shaft is subject to torque that remains within the boundaries of Hooke's Law, avoiding any permanent deformation. So, the formula for shearing strain is revisited. This formula is multiplied by the modulus of rigidity, and then Hooke's Law for the shearing stress and strain is applied. As a result, the equation for shearing stress in a shaft can be derived.
    Polar Curves01:19

    Polar Curves

    The spirograph is a versatile tool for visualizing the relationship between geometry and mathematical representation. In particular, it demonstrates how polar coordinates offer an alternative framework for describing curves in comparison to Cartesian coordinates. Instead of specifying a point by its horizontal and vertical displacements (x, y), polar coordinates use a radius r, the distance from the origin, and an angle θ, measured counterclockwise from the polar axis. This system is...
    Dielectric Polarization in a Capacitor01:31

    Dielectric Polarization in a Capacitor

    The presence of a dielectric medium in a capacitor not only changes the voltage and capacitance but also affects the electric field. In general, dielectrics can be of two types: polar and nonpolar. In a polar dielectric, the positive and negative charges in the molecules are separated by a distance and hence have a permanent dipole moment. In contrast, no such charge separation exists in a nonpolar dielectric, however the nonpolar molecules get polarized in the presence of an external electric...
    Deformation in a Circular Shaft01:10

    Deformation in a Circular Shaft

    One of the distinctive characteristics of circular shafts is their ability to maintain their cross-sectional integrity under torsion. In other words, each cross-section continues to exist as a flat, unaltered entity, simply rotating like a solid, rigid slab. To understand the distribution of shearing stress within such a shaft, consider a cylindrical section inside this circular shaft. This section has a length of L and a radius of R, with one end fixed. The radius of the cylindrical section is...