Related Experiment Video

Updated: Jul 7, 2026

Low-cost Custom Fabrication and Mode-locked Operation of an All-normal-dispersion Femtosecond Fiber Laser for Multiphoton Microscopy
08:48

Low-cost Custom Fabrication and Mode-locked Operation of an All-normal-dispersion Femtosecond Fiber Laser for Multiphoton Microscopy

Published on: November 22, 2019

Reduction of Coupling Loss in a One-to-many Collimating System for a Wavelength Division (de)Multiplexer

W S Hu, Q J Zeng, Y H Jin

    Applied Optics
    |February 21, 2008
    PubMed

    More Related Videos

    Transmission of Multiple Signals through an Optical Fiber Using Wavefront Shaping09:43

    Transmission of Multiple Signals through an Optical Fiber Using Wavefront Shaping

    Published on: March 20, 2017

    A Photonic System for Generating Unconditional Polarization-Entangled Photons Based on Multiple Quantum Interference07:56

    A Photonic System for Generating Unconditional Polarization-Entangled Photons Based on Multiple Quantum Interference

    Published on: September 5, 2019

    Related Concept Videos

    Reducing Line Loss01:18

    Reducing Line Loss

    In a three-phase circuit, line loss is an indicator of energy dissipated as heat due to the resistance of transmission lines. To address this, incorporating transformers into the system—a step-up transformer at the source and a step-down transformer at the load—is a strategic solution. Two three-phase transformers are introduced to improve this.
    With a step-up transformer at the source, the voltage is increased, thereby reducing the current in the transmission lines since power loss in...
    Design Example: Capacitance Multiplier Circuit01:20

    Design Example: Capacitance Multiplier Circuit

    In integrated circuit technology, a capacitance multiplier is often utilized to produce a larger capacitance value when a small physical capacitance falls short. This is achieved by a circuit that multiplies capacitance values by a factor of up to 1000, such that a 10-pF capacitor can replicate the performance of a 100-nF capacitor.
    The circuit illustrated in Figure 1 below incorporates two op-amps, with the first operating as a voltage follower and the second acting as an inverting amplifier.
    Clipper Circuit01:18

    Clipper Circuit

    A clipper circuit is a fundamental wave-shaping device that harnesses the unique properties of diodes to alter and control waveform characteristics. This technology is widely used in electronic devices, especially in television and radar communication systems, where it enhances waveform modulation in both transmitters and receivers.
    The operation of a clipper circuit can be exemplified by analyzing a dual-clipper configuration setup that integrates two ideal diodes, each paired with a biasing...
    Cascaded Op Amps01:16

    Cascaded Op Amps

    Operational amplifiers (op-amps) are versatile electronic components that can be interconnected in a cascade - one after another in a linear sequence. This cascading is possible due to their infinite input resistance and zero output resistance, allowing them to maintain their input-output relationships even when connected in series.
    In a cascaded system, each op-amp is referred to as a stage. The output of one stage drives the input of the subsequent stage. As the input signal passes through...
    Transmission Line Design Considerations01:23

    Transmission Line Design Considerations

    Aluminum has become the material of choice for overhead transmission lines, surpassing copper due to its abundance and cost-effectiveness. The most prevalent type is the aluminum conductor, steel-reinforced (ACSR), which combines aluminum strands around a steel core. Other variants include all-aluminum conductors (AAC), all-aluminum alloy conductors (AAAC), aluminum conductor alloy-reinforced (ACAR), and aluminum-clad steel conductors. Advanced designs, such as aluminum conductors with steel...
    Block Diagram Reduction01:22

    Block Diagram Reduction

    The process of deriving the transfer function of a control system often involves reducing its block diagram to a single block. This simplification can be achieved through a series of strategic operations, including relocating branch points and comparators. These operations preserve the overall function of the system while allowing for easier manipulation and combination of blocks.
    The first step in this process is the identification and relocation of a branch point. A branch point, where a...