Related Experiment Video

Updated: Jul 6, 2026

Fabrication Procedures and Birefringence Measurements for Designing Magnetically Responsive Lanthanide Ion Chelating Phospholipid Assemblies
09:38

Fabrication Procedures and Birefringence Measurements for Designing Magnetically Responsive Lanthanide Ion Chelating Phospholipid Assemblies

Published on: January 3, 2018

Alternating current sensor with second-harmonic detection

J A Ferrari1, C D Perciante, A Dubra

  • 1Instituto de Física, Facultad de Ingeniería, J. Herrera y Reissig 565, 11300 Montevideo, Uruguay. jferrari@fing.edu.uy

Applied Optics
|March 20, 2008
PubMed

More Related Videos

High-precision Electromagnetic Flowmeter with Empty Pipe Detection via Complex Programmable Logic Device-based Waveform Recognition05:11

High-precision Electromagnetic Flowmeter with Empty Pipe Detection via Complex Programmable Logic Device-based Waveform Recognition

Published on: June 27, 2025

Investigating the Potential of Singly Curved Thin Piezoelectric Transducers for Energy Harvesting and Structural Health Monitoring07:02

Investigating the Potential of Singly Curved Thin Piezoelectric Transducers for Energy Harvesting and Structural Health Monitoring

Published on: November 14, 2025

Related Concept Videos

Sinusoidal Sources01:18

Sinusoidal Sources

Direct current (DC) refers to an electric current that flows in a single direction, maintaining a constant polarity. This is in contrast to alternating current (AC), which periodically changes its direction and magnitude. AC forms the backbone of modern electricity transmission and distribution systems due to its efficient long-distance transmission capabilities.
In homes, the power supplies use sinusoidal sources to provide electricity. These sources generate a voltage that varies sinusoidally...
Superposition Theorem for AC Circuits01:13

Superposition Theorem for AC Circuits

Consider encountering a circuit in a steady state where all its inputs are sinusoidal, yet they do not all possess the same frequency. Such a circuit is not classified as an alternating current (AC) circuit, and consequently, its currents and voltages will not exhibit sinusoidal behavior. However, this circuit can be analyzed using the principle of superposition.
The principle of superposition stipulates that the output of a linear circuit with several concurrent inputs is equivalent to the...
Voltage Doubler Circuit01:23

Voltage Doubler Circuit

A voltage doubler circuit integrates two main components: a clamping section and a rectifier section. The clamping section consists of a capacitor (C1) and a diode (D1), whereas the rectifier section is equipped with another diode (D2) and capacitor (C2). This circuit produces an output voltage with twice the amplitude of the sinusoidal input voltage.
Second-order Op Amp Circuits01:19

Second-order Op Amp Circuits

Implementing second-order low-pass filters in audio systems is crucial in refining audio signals by eliminating undesirable high-frequency noise. These filters typically involve second-order op-amp circuits configured as voltage followers, encompassing two nodes with distinct storage elements.
The analysis of such circuits follows a systematic approach, similar to the second-order RLC circuits. In practical scenarios, bulky inductors are rarely employed due to their size and weight. This means...
Resistor in an AC Circuit01:31

Resistor in an AC Circuit

An alternating emf or voltage source is needed to supply an alternating current (AC) to a circuit. A coil of wire rotating in a magnetic field at a constant angular speed represents such a source. It also generates a sinusoidal alternating emf and serves as an industrial alternator.
One-way current through the meter is measured using diodes. A diode is a device with better conductivity in one direction compared to the other; in its ideal state, it has zero resistance in one direction and allows...
Galvanometer01:24

Galvanometer

Common devices, including car instrument panels, battery chargers, and inexpensive electrical instruments, measure potential difference (voltage), current, or resistance using a d'Arsonval galvanometer. This electromechanical instrument is also known as a moving coil galvanometer.
The galvanometer consists of  two concave-shaped permanent magnets, providing a uniform radial magnetic field in the annular region. In the center, a pivoted coil of fine copper wire is placed in the uniform magnetic...