Related Experiment Video

Updated: Jun 29, 2026

Fabrication, Densification, and Replica Molding of 3D Carbon Nanotube Microstructures
09:23

Fabrication, Densification, and Replica Molding of 3D Carbon Nanotube Microstructures

Published on: July 2, 2012

Strong and ductile colossal carbon tubes with walls of rectangular macropores

Huisheng Peng1, Daoyong Chen, Jian-Yu Huang

  • 1The Institute for Advanced Materials & Nano Biomedicine, Tongji University, Shanghai 200092, China. penghs2004@yahoo.com

Physical Review Letters
|October 15, 2008
PubMed

More Related Videos

A Salt-Templated Synthesis Method for Porous Platinum-based Macrobeams and Macrotubes13:08

A Salt-Templated Synthesis Method for Porous Platinum-based Macrobeams and Macrotubes

Published on: May 18, 2020

Precision Milling of Carbon Nanotube Forests Using Low Pressure Scanning Electron Microscopy08:10

Precision Milling of Carbon Nanotube Forests Using Low Pressure Scanning Electron Microscopy

Published on: February 5, 2017

Related Concept Videos

Thin-Walled Hollow Shafts01:15

Thin-Walled Hollow Shafts

In analyzing a thin-walled hollow shaft subjected to torsional loading, a segment with width dx is isolated for examination. Despite its equilibrium state, this segment faces torsional shearing forces at its ends. These forces are quantitatively described by the product of the longitudinal shearing stress on the segment's minor surface and the area of this surface, leading to the concept of shear flow. This shear flow is consistent throughout the structure, indicating a uniform distribution of...
Steady, Laminar Flow in Circular Tubes01:23

Steady, Laminar Flow in Circular Tubes

Hagen-Poiseuille flow describes a viscous fluid's steady, incompressible flow through a cylindrical tube with a constant radius R. This flow profile is often applied to understand fluid transport in narrow channels, such as capillaries. It serves as a foundational example of laminar flow. In this model, cylindrical coordinates (r,θ,z) are used to describe the radial (r), angular (θ), and axial (z) dimensions within the tube. For Hagen-Poiseuille flow, the velocity profile is purely axial,...
Network Covalent Solids02:18

Network Covalent Solids

Network covalent solids contain a three-dimensional network of covalently bonded atoms as found in the crystal structures of nonmetals like diamond, graphite, silicon, and some covalent compounds, such as silicon dioxide (sand) and silicon carbide (carborundum, the abrasive on sandpaper). Many minerals have networks of covalent bonds.
To break or to melt a covalent network solid, covalent bonds must be broken. Because covalent bonds are relatively strong, covalent network solids are typically...
Generation of Straight or Branched Actin Filaments01:14

Generation of Straight or Branched Actin Filaments

The straight or branched structure formation of actin filaments is controlled by nucleating proteins such as the formins and Arp2/3 complex. Formin-mediated assembly results in straight filaments, whereas Arp2/3 protein complex-mediated assembly results in branched actin filaments.
Arp2/3 Complex
Arp2/3 complex is a seven-subunit complex consisting of two proteins similar to actin- Arp2 and Arp3, and five other subunits that help keep Arp2 and Arp3 inactive. When required, the complex is...
Pore Size Distribution01:23

Pore Size Distribution

In concrete, the pore size distribution significantly influences the material's properties. Capillary pores, markedly larger than gel pores, form a vast network within partially hydrated cement paste, reducing the concrete's strength and increasing its permeability. This heightened permeability leads to a greater risk of damage from environmental factors like freeze-thaw cycles and chemical attacks, with the extent of vulnerability also being tied to the water-to-cement ratio.
Adequate...
Yield Criteria for Ductile Materials under Plane Stress01:25

Yield Criteria for Ductile Materials under Plane Stress

In designing structural elements and machine parts using ductile materials, it is crucial to ensure that these components withstand applied stresses without yielding. Yielding is initially determined through a tensile test, which evaluates the material's response to uniaxial stress. However, tensile stress is insufficient when components face biaxial or plane stress conditions This condition requires advanced criteria to predict failure.
The Maximum Shearing Stress Criterion, also known as the...