Search research articles

ABOUT JoVE

Overview Leadership Blog JoVE Help Center

AUTHORS

Publishing Process Editorial Board Scope & Policies Peer Review FAQ Submit

LIBRARIANS

Testimonials Subscriptions Access Resources Library Advisory Board FAQ

RESEARCH

JoVE Journal Methods Collections JoVE Encyclopedia of Experiments Archive

EDUCATION

JoVE Core JoVE Business JoVE Science Education JoVE Lab Manual Faculty Resource Center Faculty Site

Terms & Conditions of Use

Related Concept Videos

Two Components: Liquid–Liquid Systems

Two Components: Liquid–Liquid Systems

A pressure-composition phase diagram explicitly describes the behavior of an ideal solution of two volatile liquids under varying pressures and compositions. A pressure-composition diagram has two main curves. The bubble point curve represents the plot of pressure versus liquid mole fraction. It indicates the pressure at which the first bubble of vapor forms from the liquid phase as the system pressure decreases.The dew point curve is the pressure versus vapor mole fraction. It indicates the...

Liquid–Solid Solutions

Liquid–Solid Solutions

The process of a solid dissolving in a liquid to form a solution is governed by the solubility limit, which is the maximum amount of the solid substance, or solute, that can be dissolved in a specific volume of the liquid or solvent. As the solute dissolves, it reaches a point where no more solute can be dissolved at a given temperature - this is known as the saturation point. However, if further solute is added and it manages to dissolve, the solution becomes supersaturated. Supersaturated...

Nonideal Two-Component Liquid Solutions

Nonideal Two-Component Liquid Solutions

Nonideal liquid solutions, also known as real solutions, do not strictly follow Raoult's law. Raoult's law is a rule of thumb in physical chemistry. However, not all mixtures adhere to this law due to varying molecular interactions. For example, in an acetone/chloroform solution, the individual vapor pressures of the components are lower than expected, resulting in a total vapor pressure below that predicted by Raoult's law, causing a negative deviation.On the other hand, in an ethanol/water...

Network Covalent Solids

Network Covalent Solids

Network covalent solids contain a three-dimensional network of covalently bonded atoms as found in the crystal structures of nonmetals like diamond, graphite, silicon, and some covalent compounds, such as silicon dioxide (sand) and silicon carbide (carborundum, the abrasive on sandpaper). Many minerals have networks of covalent bonds.
To break or to melt a covalent network solid, covalent bonds must be broken. Because covalent bonds are relatively strong, covalent network solids are typically...

You might also read

Related Articles

Articles linked to this work by shared authors, journal, and citation graph.

Sort by

Same author

Phase engineering of atomically thin magnetic chromium tellurides via molecular beam epitaxy.

Nature communications·2026

Same author

Boosting Ferroelectricity: 2D and Polymer Ferroelectric Hybrids Enabling Ambipolar Nonvolatile MoS<sub>2</sub> Memory Transistor.

Advanced science (Weinheim, Baden-Wurttemberg, Germany)·2026

Same author

Hierarchical on-surface assembly of nanoribbons through concurrent hydrogen- and chalcogen-bonding interactions.

Chemical science·2026

Same author

Programmable ion-protein networks from sodium caseinate: a sustainable platform for soft functional materials.

Materials horizons·2026

Same author

Ultra-narrow donor-acceptor nanoribbons.

Nature communications·2026

Same author

Nanoporous BNC network on Au(111) from a borazine-based arylalkyne.

Chemical communications (Cambridge, England)·2026

Search research articles

Related Experiment Video

Updated: Jun 28, 2026

Preparation of Highly Porous Coordination Polymer Coatings on Macroporous Polymer Monoliths for Enhanced Enrichment of Phosphopeptides

Preparation of Highly Porous Coordination Polymer Coatings on Macroporous Polymer Monoliths for Enhanced Enrichment of Phosphopeptides

Published on: July 14, 2015

Pre-programmed bicomponent porous networks at the solid-liquid interface: the low concentration regime.

Carlos-Andres Palma¹, Massimo Bonini, Anna Llanes-Pallas

¹Nanochemistry Laboratory, ISIS/CNRS 7006, Université Louis Pasteur, 8 allée Gaspard Monge, Strasbourg, France.

Chemical Communications (Cambridge, England)

|November 6, 2008

Summary

Researchers achieved control over bicomponent porous network formation using self-assembly. This was accomplished by leveraging triple hydrogen bonds between melamine and bis-uracyl modules at the solid-liquid interface.

More Related Videos

A Microfluidic Platform to Study Bioclogging in Porous Media

A Microfluidic Platform to Study Bioclogging in Porous Media

Published on: October 13, 2022

Bilayer Microfluidic Device for Combinatorial Plug Production

Bilayer Microfluidic Device for Combinatorial Plug Production

Published on: December 1, 2023

Related Experiment Videos

Last Updated: Jun 28, 2026

Preparation of Highly Porous Coordination Polymer Coatings on Macroporous Polymer Monoliths for Enhanced Enrichment of Phosphopeptides

Preparation of Highly Porous Coordination Polymer Coatings on Macroporous Polymer Monoliths for Enhanced Enrichment of Phosphopeptides

Published on: July 14, 2015

A Microfluidic Platform to Study Bioclogging in Porous Media

A Microfluidic Platform to Study Bioclogging in Porous Media

Published on: October 13, 2022

Bilayer Microfluidic Device for Combinatorial Plug Production

Bilayer Microfluidic Device for Combinatorial Plug Production

Published on: December 1, 2023

Area of Science:

Supramolecular chemistry
Materials science
Nanotechnology

Background:

Self-assembly is a key process in creating ordered structures.
Controlling the formation of multicomponent materials is challenging.
Hydrogen bonding plays a crucial role in molecular recognition and self-assembly.

Purpose of the Study:

To achieve controlled formation of a bicomponent porous network.
To investigate the role of specific molecular interactions in directed self-assembly.
To explore the use of melamine and bis-uracyl modules for creating functional porous materials.

Main Methods:

Utilizing self-assembly at the solid-liquid interface.
Employing triple hydrogen bonds for molecular recognition between melamine and bis-uracyl.
Characterizing the resulting bicomponent porous network structure.

Main Results:

Successful formation of a bicomponent porous network was demonstrated.
The triple hydrogen bonding interaction between melamine and bis-uracyl effectively directed the self-assembly process.
The solid-liquid interface facilitated the controlled organization of the molecular modules.

Conclusions:

Self-assembly at the solid-liquid interface, driven by specific hydrogen bonding, enables precise control over bicomponent porous network formation.
Melamine and bis-uracyl modules are effective building blocks for constructing ordered porous materials.
This approach offers a pathway for designing advanced porous materials with tailored properties.