Related Experiment Video

Updated: Jun 27, 2026

Induction of Microstreaming by Nonspherical Bubble Oscillations in an Acoustic Levitation System
08:19

Induction of Microstreaming by Nonspherical Bubble Oscillations in an Acoustic Levitation System

Published on: May 9, 2021

Bifurcational mechanisms of synchronization of a resonant limit cycle on a two-dimensional torus

V Anishchenko1, S Nikolaev, J Kurths

  • 1Institute of Nonlinear Dynamics, Department of Physics, Saratov State University, 410012 Saratov, Russia. wadim@chaos.ssu.runnet.ru

Chaos (Woodbury, N.Y.)
|December 3, 2008
PubMed

More Related Videos

Microwave Photonics Systems Based on Whispering-gallery-mode Resonators12:18

Microwave Photonics Systems Based on Whispering-gallery-mode Resonators

Published on: August 5, 2013

Rapid Repetition Rate Fluctuation Measurement of Soliton Crystals in a Microresonator07:42

Rapid Repetition Rate Fluctuation Measurement of Soliton Crystals in a Microresonator

Published on: December 15, 2021

Related Concept Videos

Sound Waves: Resonance01:14

Sound Waves: Resonance

Resonance is produced depending on the boundary conditions imposed on a wave. Resonance can be produced in a string under tension with symmetrical boundary conditions (i.e., has a node at each end). A node is defined as a fixed point where the string does not move. The symmetrical boundary conditions result in some frequencies resonating and producing standing waves, while other frequencies interfere destructively. Sound waves can resonate in a hollow tube, and the frequencies of the sound...
Concept of Resonance and its Characteristics01:19

Concept of Resonance and its Characteristics

If a driven oscillator needs to resonate at a specific frequency, then very light damping is required. An example of light damping includes playing piano strings and many other musical instruments. Conversely, to achieve small-amplitude oscillations as in a car's suspension system, heavy damping is required. Heavy damping reduces the amplitude, but the tradeoff is that the system responds at more frequencies. Speed bumps and gravel roads prove that even a car's suspension system is not immune...
Torsional Pendulum01:09

Torsional Pendulum

A torsional pendulum involves the oscillation of a rigid body in which the restoring force is provided by the torsion in the string from which the rigid body is suspended. Ideally, the string should be massless; practically, its mass is much smaller than the rigid body's mass and is neglected.
As long as the rigid body's angular displacement is small, its oscillation can be modeled as a linear angular oscillation. The amplitude of the oscillation is an angle. The role of mass is played by the...
Limits with Oscillating Discontinuities01:19

Limits with Oscillating Discontinuities

An oscillating discontinuity is a type of discontinuity in which a function’s values fluctuate infinitely often as the input approaches a particular point. Unlike jump discontinuities, where the function suddenly shifts between two values, or infinite discontinuities, where the function diverges without bound, an oscillating discontinuity arises from rapid back-and-forth variation. Because the function never stabilizes toward a single value, no finite limit exists at that point.One of the most...
Forced Oscillations01:06

Forced Oscillations

When an oscillator is forced with a periodic driving force, the motion may seem chaotic. The motions of such oscillators are known as transients. After the transients die out, the oscillator reaches a steady state, where the motion is periodic, and the displacement is determined.
Design Example: Underdamped Parallel RLC Circuit01:17

Design Example: Underdamped Parallel RLC Circuit

Consider designing an oscillator circuit, a crucial component in various electronic devices and systems. The objective is to create an oscillator circuit with specific characteristics: a damped natural frequency of 4 kHz and a damping factor of 4 radians per second. To accomplish this, a parallel RLC circuit is employed, known for its ability to sustain oscillations at a resonant frequency. In this case, the damping factor is pivotal in achieving the desired performance.
Starting with a fixed...