Related Experiment Video
Updated: Jun 27, 2026
05:48
Analysis of Volatile and Oxidation Sensitive Compounds Using a Cold Inlet System and Electron Impact Mass Spectrometry
Published on: September 5, 2014
Use of membrane micropumps for introducing the sample solution in flame atomic absorption spectrometry
Ignacio López-García1, Joanna Kozak, Manuel Hernández-Córdoba
1Department of Analytical Chemistry, Faculty of Chemistry, University of Murcia, E-30071 Murcia, Spain.
Talanta
|December 17, 2008
Summary
Membrane micropumps enhance flame atomic absorption spectrometry (FAAS) by simplifying calibration and enabling on-line sample dilution. This technology offers novel data analysis through pulsed absorbance profiles and Fourier transformations.
Area of Science:
- Analytical Chemistry
- Spectroscopy
Background:
- Flame atomic absorption spectrometry (FAAS) is a common technique for elemental analysis.
- Traditional FAAS methods can be limited by sample introduction and calibration procedures.
Purpose of the Study:
- To discuss the advantages of using membrane micropumps in FAAS.
- To explore novel data analysis methods for FAAS.
Main Methods:
- Utilized two computer-controlled manifolds with membrane micropumps for sample introduction.
- Obtained a wide range of dispersion coefficients.
- Applied Fourier transformation to pulsed absorbance-time profiles.
Main Results:
- Micropumps facilitate calibration using a single standard solution.
- Enabled on-line dilution of concentrated samples.
- Generated amplitude-frequency plots from absorbance data.
Conclusions:
- Membrane micropumps offer significant advantages for sample introduction in FAAS.
- Pulsed absorbance data analysis provides an innovative approach to interpreting FAAS results.
Related Concept Videos
01:25Atomic Absorption Spectroscopy: Atomization Methods
Atomic Absorption Spectroscopy (AAS) atomizes samples through flame atomization or electrothermal atomization. Flame atomization typically involves a nebulizer and spray chamber assembly to combine the sample with a fuel–oxidant mixture, creating a fine aerosol mist that enters a burner. Typically, the fuel and oxidant are combined in an approximately stoichiometric ratio. However, for atoms that are easily oxidized, a fuel-rich mixture may be more advantageous. Only about 5% of the aerosol...
01:21Atomic Absorption Spectroscopy: Lab
For AAS measurements, samples must be introduced as clear solutions, often requiring extensive preliminary treatment to dissolve materials like soils, animal tissues, and minerals. Common methods for sample preparation include treatment with hot mineral acids, wet ashing, combustion in closed containers, high-temperature ashing, or fusion with reagents.
Solutions containing organic solvents, such as low-molecular-mass alcohols, esters, or ketones, enhance absorbances by increasing nebulizer...
Solutions containing organic solvents, such as low-molecular-mass alcohols, esters, or ketones, enhance absorbances by increasing nebulizer...
01:02Flame Photometry: Overview
Flame photometry, also known as flame emission spectrometry, is a technique used for the qualitative and quantitative analysis of elements present in a sample using a flame as the source of excitation energy. The concept of flame photometry was realized in the early 1860s by Kirchhoff and Bunsen, who discovered that specific elements emit characteristic radiation when excited in flames. The first instrument developed for this purpose was used to measure sodium (Na) in plant ash using a Bunsen...
01:29Atomic Fluorescence Spectroscopy
Atomic fluorescence spectroscopy (AFS) is an analytical technique that involves the electronic transitions of atoms in a flame, furnace, or plasma being excited by electromagnetic (EM) radiation. When these atoms absorb energy, they become excited and subsequently release energy as they return to their original state. This emitted light, or "fluorescence," is observed at a right angle to the incident beam. Both absorption and emission processes transpire at distinct wavelengths, which are...
01:16Flame Photometry: Lab
In a flame photometer, when a solution like potassium chloride is aspirated into the flame, the solvent evaporates, leaving behind dehydrated salt. This salt dissociates into free gaseous atoms in their ground state. Some of these atoms absorb energy from the flame, leading to their excitation. The excited atoms return to the ground state, emitting photons at characteristic wavelengths. Because only electronic transitions are involved, the resulting emission lines are very narrow. The intensity...
01:22Atomic Emission Spectroscopy: Instrumentation
The instrumentation of atomic emission spectrometry (AES) involves various components, including atomization devices that convert samples into gas-phase atoms and ions. There are two main types of atomization devices: continuous and discrete atomizers. Continuous atomizers, like plasmas and flames, introduce samples in a constant stream, while discrete atomizers inject individual samples using syringes or autosamplers. The most common discrete atomizer is the electrothermal atomizer.