Related Experiment Video

Updated: Jun 24, 2026

Rapid Repetition Rate Fluctuation Measurement of Soliton Crystals in a Microresonator
07:42

Rapid Repetition Rate Fluctuation Measurement of Soliton Crystals in a Microresonator

Published on: December 15, 2021

High-power millimeter-wave rotary joint

T H Chang1, B R Yu

  • 1Department of Physics, National Tsing Hua University, Hsinchu 300, Taiwan. thschang@phys.nthu.edu.tw

The Review of Scientific Instruments
|April 2, 2009
PubMed

More Related Videos

Fabricating van der Waals Heterostructures with Precise Rotational Alignment09:25

Fabricating van der Waals Heterostructures with Precise Rotational Alignment

Published on: July 5, 2019

Microwave Photonics Systems Based on Whispering-gallery-mode Resonators12:18

Microwave Photonics Systems Based on Whispering-gallery-mode Resonators

Published on: August 5, 2013

Related Concept Videos

Atomic Force Microscopy01:08

Atomic Force Microscopy

Atomic force microscopy (AFM) is a type of scanning probe microscopy that can analyze topographic details of various specimens like ceramics, glass, polymers, and biological samples. AFM offers over 1000 times more resolution than the optical imaging system. Images generated from AFM are three-dimensional surface profiles, offering an advantage over the flat, two-dimensional images from other imaging techniques.
The AFM Probe
The probe is regarded as the heart of any AFM setup and comprises the...
Circular Shaft - Stresses in Linear Range01:13

Circular Shaft - Stresses in Linear Range

Consider a scenario where a circular shaft is subject to torque that remains within the boundaries of Hooke's Law, avoiding any permanent deformation. So, the formula for shearing strain is revisited. This formula is multiplied by the modulus of rigidity, and then Hooke's Law for the shearing stress and strain is applied. As a result, the equation for shearing stress in a shaft can be derived.
Work and Power for Rotational Motion01:27

Work and Power for Rotational Motion

Work and power in rotational motion are completely analogous to work and power in translational motion. The total work done to rotate a rigid body through an angle 'θ' about a fixed axis is the sum of the torques integrated over the angular displacement. Hence, torque and angular displacement in rotational motion are analogous to force and linear displacement in translational motion, respectively.
Similarly, the power delivered to a system that is rotating about a fixed axis is given by the...
Magnetic Field Due to Two Straight Wires01:18

Magnetic Field Due to Two Straight Wires

Consider two parallel straight wires carrying a current of 10 A and 20 A in the same direction and separated by a distance of 20 cm. Calculate the magnetic field at a point "P2", midway between the wires. Also, evaluate the magnetic field when the direction of the current is reversed in the second wire.
Maximum Power Transfer01:16

Maximum Power Transfer

Numerous practical applications within engineering disciplines, such as telecommunications, necessitate optimizing power delivery to a connected load. This pursuit, however, entails inherent internal losses, which can either equal or exceed the power supplied to the load. The Thevenin equivalent circuit is helpful in finding the maximum power a linear circuit can deliver to a load. It is assumed in this context that the load resistance can be adjusted.
By substituting the entire circuit with...
Angle of Twist: Problem Solving01:13

Angle of Twist: Problem Solving

An electric motor applies a torque of 700 N·m to an aluminum shaft, triggering a stable rotation. Two pulleys, B and C, are subjected to torques of 300 N·m and 400 N·m, respectively. The modulus of rigidity is provided as 25 GPa. With the knowledge of the length and diameter of each segment, the twist angle between the two pulleys can be computed. First, a section cut is made between pulleys B and C, and the cut cross-section is analyzed using a free-body diagram. Given that the torque exerted...