Related Experiment Video

Updated: Jun 23, 2026

Laboratory Production of Biofuels and Biochemicals from a Rapeseed Oil through Catalytic Cracking Conversion
11:33

Laboratory Production of Biofuels and Biochemicals from a Rapeseed Oil through Catalytic Cracking Conversion

Published on: September 2, 2016

Construction of combustion models for rapeseed methyl ester bio-diesel fuel for internal combustion engine

Valeri I Golovitchev1, Junfeng Yang

  • 1Department of Applied Mechanics, Chalmers University of Technology, S-412 96, Göteborg, Sweden. valeri@chalmers.se

Biotechnology Advances
|May 5, 2009
PubMed

More Related Videos

Combustion Characterization and Model Fuel Development for Micro-tubular Flame-assisted Fuel Cells08:16

Combustion Characterization and Model Fuel Development for Micro-tubular Flame-assisted Fuel Cells

Published on: October 2, 2016

Combustion Chemistry of Fuels: Quantitative Speciation Data Obtained from an Atmospheric High-temperature Flow Reactor with Coupled Molecular-beam Mass Spectrometer07:24

Combustion Chemistry of Fuels: Quantitative Speciation Data Obtained from an Atmospheric High-temperature Flow Reactor with Coupled Molecular-beam Mass Spectrometer

Published on: February 19, 2018

Related Concept Videos

Biofuels01:25

Biofuels

The microbial conversion of organic matter into biofuels holds potential as a renewable energy source. Among biofuel sources, microalgae are recognized as a highly efficient and adaptable feedstock for biodiesel production, owing to their rapid biomass accumulation, elevated lipid productivity, and capacity to proliferate in diverse aquatic systems, including freshwater, marine, and wastewater habitats. Unlike terrestrial crops, microalgae do not compete for land and can achieve significantly...
Internal Combustion Engine01:20

Internal Combustion Engine

The internal combustion engine is a heat engine that uses the byproducts of combustion as the working fluid instead of using a heat transfer medium to transfer heat. The combustion is done in a way that produces high-pressure combustion products that can be expanded through a turbine or piston to create work. Internal combustion engines can again be categorized into three kinds: (1) spark ignition gasoline engines, most commonly used in automobiles, (2) compression ignition diesel engines that...
Combustion Energy: A Measure of Stability in Alkanes and Cycloalkanes02:14

Combustion Energy: A Measure of Stability in Alkanes and Cycloalkanes

The low reactivity in alkanes can be attributed to the non-polar nature of C–C and C–H σ bonds. Alkanes, therefore, were  initially termed as “paraffins,” derived from the Latin words: parum, meaning “too little,” and affinis, meaning “affinity.”
Alkanes undergo combustion in the presence of excess oxygen and high-temperature conditions to give carbon dioxide and water. A combustion reaction is the energy source in natural gas, liquified petroleum gas (LPG), fuel oil, gasoline, diesel fuel, and...
Otto and Diesel Cycle01:27

Otto and Diesel Cycle

An Otto engine is a four-stroke engine that uses a mixture of gasoline and air as the working fuel. The fuel is injected into the cylinder, and the piston is moved completely down so that the cylinder is at maximum volume. By moving the piston up, adiabatic compression takes place. The spark plug ignites the gasoline-air mixture, and the burning fuel adds heat to the system at a constant volume. The heated mixture expands adiabatically and gets further cooled by exhausting heat, and this cyclic...
Standard Enthalpy of Formation02:37

Standard Enthalpy of Formation

Enthalpy changes are typically tabulated for reactions in which both the reactants and products are at the same conditions. A standard state is a commonly accepted set of conditions used as a reference point for the determination of properties under other different conditions. For chemists, the IUPAC standard state refers to materials under a pressure of 1 bar and solutions at 1 M and does not specify a temperature. Many thermochemical tables list values with a standard state of 1 atm. Because...
Work Done in an Adiabatic Process01:20

Work Done in an Adiabatic Process

Consider the adiabatic compression of an ideal gas in the cylinder of an automobile diesel engine. The gasoline vapor is injected into the cylinder of an automobile engine when the piston is in its expanded position. The temperature, pressure, and volume of the resulting gas-air mixture are 20 °C, 1.00 x 105 N/m2, and 240 cm3 , respectively. The mixture is then compressed adiabatically to a volume of 40 cm3. Note that, in the actual operation of an automobile engine, the compression is not...