Related Experiment Video

Updated: Jun 23, 2026

Analysis and Specification of Starch Granule Size Distributions
08:46

Analysis and Specification of Starch Granule Size Distributions

Published on: March 4, 2021

[Studies relationship between powder characteristic of kinds of granules and their hygroscopicity]

Shuping Sun1, Liuqing Di

  • 1Wannan Medical College, Wuhu 241002, China. sun5587001@163.com

Zhongguo Zhong Yao Za Zhi = Zhongguo Zhongyao Zazhi = China Journal of Chinese Materia Medica
|May 19, 2009
PubMed
Abstract

More Related Videos

Frugal Imaging Technique of Capillary Flow Through Three-Dimensional Polymeric Printing Powders06:01

Frugal Imaging Technique of Capillary Flow Through Three-Dimensional Polymeric Printing Powders

Published on: October 4, 2022

A System to Create Stable Nanoparticle Aerosols from Nanopowders12:59

A System to Create Stable Nanoparticle Aerosols from Nanopowders

Published on: July 26, 2016

Related Concept Videos

Moisture Content and Bulking of Aggregate01:10

Moisture Content and Bulking of Aggregate

The moisture content of aggregates is a crucial factor in construction, particularly in concrete mixing, as it influences the total water required in the mix. Moisture content represents the water coated on the exterior surface of the aggregate existing in a saturated and surface-dry condition. The total water content of a moist aggregate is the sum of its moisture content and water absorption.
When aggregates are exposed to rain or sit in stockpiles, they absorb moisture, which must be...
Porosity and Absorption of Aggregate01:20

Porosity and Absorption of Aggregate

Aggregates contain pores of varying sizes; while some are completely enclosed within the particles, others open onto the surface, allowing water to penetrate. The porosity of aggregates is a major factor contributing to the overall porosity of concrete, given that aggregates constitute about three-quarters of concrete's volume.
When all pores in an aggregate are filled with water, the aggregate is considered saturated and surface-dry. If left in dry air, water will evaporate until the aggregate...
Precipitate Formation and Particle Size Control01:16

Precipitate Formation and Particle Size Control

In precipitation gravimetry, the precipitating agent should react specifically or selectively with the analyte. While a specific reagent reacts with the analyte alone, a selective reagent can react with a limited number of chemical species.
The obtained precipitate should be either a pure substance of known composition or easily converted to one by a simple process, such as ignition or drying. In addition, the precipitate should be insoluble and easily filterable. In general, filterability...
Fineness of Cement01:15

Fineness of Cement

The fineness of cement directly influences the rate of hydration, as the hydration begins at the surface of the cement particles. In addition to hydration, the fineness of cement is vital for various properties of concrete including workability, gypsum requirement, and long-term behavior. The fineness of cement is represented in terms of the specific surface of cement which is typically measured in square meters per kilogram, with several methods available for this determination.
Direct...
Pore Size Distribution01:23

Pore Size Distribution

In concrete, the pore size distribution significantly influences the material's properties. Capillary pores, markedly larger than gel pores, form a vast network within partially hydrated cement paste, reducing the concrete's strength and increasing its permeability. This heightened permeability leads to a greater risk of damage from environmental factors like freeze-thaw cycles and chemical attacks, with the extent of vulnerability also being tied to the water-to-cement ratio.
Adequate...
Specific Gravity of Aggregate01:19

Specific Gravity of Aggregate

Aggregates typically contain pores, which can be either permeable or impermeable. Considering the pores in the aggregates, the specific gravity of aggregates is defined in three different forms, namely, bulk or gross specific gravity, apparent specific gravity, and absolute specific gravity.
Bulk or gross specific gravity is calculated by taking the ratio of the mass of aggregates in the saturated surface-dry state to the total volume that includes both the solids and the voids within the...