Related Experiment Video

Updated: Jun 22, 2026

Low-cost Custom Fabrication and Mode-locked Operation of an All-normal-dispersion Femtosecond Fiber Laser for Multiphoton Microscopy
08:48

Low-cost Custom Fabrication and Mode-locked Operation of an All-normal-dispersion Femtosecond Fiber Laser for Multiphoton Microscopy

Published on: November 22, 2019

Transient propagation mode of fiber fuse leaving no voids

Shin-Ichi Todoroki

    Optics Express
    |June 9, 2009
    PubMed

    More Related Videos

    Fabrication of 1-D Photonic Crystal Cavity on a Nanofiber Using Femtosecond Laser-induced Ablation13:02

    Fabrication of 1-D Photonic Crystal Cavity on a Nanofiber Using Femtosecond Laser-induced Ablation

    Published on: February 25, 2017

    Fabrication and Testing of Microfluidic Optomechanical Oscillators09:10

    Fabrication and Testing of Microfluidic Optomechanical Oscillators

    Published on: May 29, 2014

    Related Concept Videos

    Propagation Speed of Electromagnetic Waves01:30

    Propagation Speed of Electromagnetic Waves

    Electromagnetic waves are consistent with Ampere's law. Assuming there is no conduction current Ampere's law is given as:
    Series R—L Circuit Transients01:22

    Series R—L Circuit Transients

    In a series resistor-inductor (R-L) circuit, closing the switch at the start of the time period simulates a three-phase short circuit, a fault condition where all three phases of an unloaded synchronous machine are short-circuited. When there is no fault impedance and no initial current, the initial voltage is determined by the phase angle of the source voltage.
    Using Kirchhoff's Voltage Law (KVL) to analyze this circuit helps determine the total asymmetrical fault current, which consists of...
    Fiber Reinforced Concrete01:22

    Fiber Reinforced Concrete

    Fiber-reinforced concrete significantly enhances the structural and nonstructural properties of traditional concrete by incorporating fibers like steel, glass, and polymers. These fibers, varying from natural ones such as sisal and cellulose to manufactured ones like polypropylene and Kevlar, are mixed into hydraulic cement with aggregates. Steel fibers, often preferred for their robustness, contribute to improved ductility, toughness, and post-cracking performance. The concrete is classified...
    Reclosers and Fuses01:26

    Reclosers and Fuses

    Automatic circuit reclosers enhance the protection of distribution circuits by interrupting and auto-reclosing an AC circuit according to a preset sequence. They effectively manage temporary faults on overhead distribution lines, often caused by tree limbs or wildlife, by briefly disrupting service to improve overall reliability. However, contact with reclosers or energized broken conductors on the ground can pose serious hazards.
    A comprehensive protection scheme for radial distribution...
    Lossless Lines01:23

    Lossless Lines

    In electrical engineering, a lossless transmission line is characterized by a purely imaginary propagation constant and a resistive characteristic impedance. The ABCD parameters, which describe the relationship between the input and output voltages and currents, indicate an equivalent π circuit with an imaginary series impedance and a shunt admittance. This results in a transmission line that, when the product of the phase constant (beta) and the length of the line is less than pi, exhibits...
    MOSFET: Depletion Mode01:20

    MOSFET: Depletion Mode

    Depletion-mode MOSFETs represent a unique subset of MOSFET technology, functioning fundamentally differently from their enhancement-mode counterparts. Unlike enhancement MOSFETs, which require a positive gate-source voltage (Vgs) to turn on, depletion-mode MOSFETs are inherently conductive and "normally on" devices.
    The primary characteristic of depletion-mode MOSFETs is their ability to conduct current between the drain and source terminals without gate bias. This inherent conductivity arises...